RIDGID 122XL manual Machine Assembly, Specifications, Standard Equipment, Accessories

Page 6

122XL Copper Cutting and Prep Machine

tubing. The brush cleans the external surface in prepa- ration for joining. Deburring disk cleans burrs from the out- side surface of the tubing.

Model 122XL Copper Cutting And Prep Machine can also clean the inside of fittings using individually sized brushes that are attached to motor-driven quick change adapter. It can also be used to cut and debur 1/2through 4stainless steel tubing with a maximum wall thick- ness of .065.

Specifications

Capacity

1/2– 4Diameter

 

Copper Tube & Fittings

 

(Types K, L, and M)

 

(Stainless Steel Tube 0.065

 

Maximum Wall Thickness)

Maximum

 

Reamer Capacity

2Diameter Tubing

Motor:

 

Type

115V/60Hz Induction

Horsepower

1/3 HP @ 1750 RPM

Amps

6.0

Switch

ON

Rocker Type

Weight

OFF

72 lbs. (32.7 kg)

Dimensions:

 

Height

16.5(42 cm)

Width

17.1(43 cm)

Depth

17.0(38 cm)

Standard Equipment

Model No.

Cat. No.

Description

122XL

10973

Copper Cutting and Prep Machine

 

 

115V, 60Hz w/Reamer and O.D

 

 

Deburring Disk

 

 

 

Accessories

Cat. No.

Description

36662

Model 301A Foot Switch – 120V

93717

1/2Fitting Brush (Pkg. of 3)

93722

3/4Fitting Brush (Pkg. of 3)

93727

1Fitting Brush (Pkg. of 3)

93732

11/4Fitting Brush (Pkg. of 3)

93737

11/2Fitting Brush (Pkg. of 3)

93742

2Fitting Brush (Pkg. of 3)

12638

21/2Fitting Brush (Pkg. of 3)

12643

3- 4Fitting Brush (Pkg. of 3)

93747

Quick-Change Adapter f/Fitting Brush

93712

Fitting Brush Holder

33551

Cutter Wheel f/Copper and Stainless Steel

10343

Wheel Pin for 33551 Cutter Wheel

42295

Outside Diameter Cleaning Brush

42360

1206 Stand

 

 

Figure 1 – 122XL Copper Cutting and Prep Machine

Fitting

Brushes

Adapter

Figure 2 – Fitting Brushes/Quick-Change Adapter, and Mounting Hardware

Machine Assembly

WARNING

To prevent serious injury, proper assembly of the No. 122XL Copper Cutting and Prep Machine is required. The following procedures should be followed:

WARNING Make sure machine is unplugged from power source before assembling accessories or making any adjustments.

Fitting Brushes and Holder

(Optional Accessory)

1.Mount the fitting brush holder to No. 122XL Copper Cutting and Prep Machine by using the two Phillips head screws provided with the rack (Figure 2). Use the two pre-drilled holes to fasten the rack to the side of the housing.

2.Attach the quick change adapter to front roller shaft extending from the machine housing using the set

4

Ridge Tool Company

Image 6
Contents 122XL Copper Cutting and Prep Machine Table of Contents 122XL Copper Cutting and Prep Machine Electrical Safety General Safety InformationWork Area Safety Personal SafetySpecific Safety Information Description, Specifications and Standard EquipmentAccessories Machine AssemblySpecifications Standard EquipmentMachine Inspection Machine and Work Area Set-UpMounting on No Stand Operating Instructions Cutting TubeCleaning/Deburring O.D. of Tube Turn ON/OFF switch to the OFF positionAccessories Cleaning Inside of FittingsReaming I.D. of Tube Maintenance Instructions Motor Machine Storage Service and RepairWiring Diagram 115V 60Hz 100V 50/60Hz 220 240V/50HzMachine à couper et à préparer le cuivre modèle 122XL Table des matières Sécurité électrique Consignes générales de sécuritéSécurité du chantier Sécurité individuelleUtilisation et entretien des outils Service après-venteConsignes de sécurité particulières Sécurité de la machineSpécifications AccessoiresDescription, spécifications et équipements de base Equipements de baseAssemblage de la machine Installation sur trépied typeAccessoire facultatif Inspection de la machinePréparation de la machine et du chantier Utilisation de la machine Coupe des tuyauxNettoyage et ébarbage de l’extérieur du tuyau Alésage de l’intérieur des tuyauxAccessoires Nettoyage de l’intérieur des raccordsEntretien Schéma électrique Stockage de la machineEntretien et réparations MoteurMáquina cortadora y preparadora de tubos de cobre 122XL Índice Seguridad eléctrica Información general de seguridadSeguridad en la zona de trabajo Seguridad personalServicio Información específica de seguridadUso y cuidado de la máquina Seguridad de la máquinaEspecificaciones Descripción, especificaciones y equipo estándarDescripción Equipo estándarEscobillas limpiafittings y su portaescobillas Montaje de la máquinaRevisión de la máquina Montaje en el Soporte NoPreparación de la máquina y de la zona de trabajo Instrucciones de funcionamiento Corte de tubosMueva el interruptor de ON/OFF a la posición de OFF apagado Accesorios Escariado del diámetro interior del tuboLimpieza del interior de un fitting Instrucciones para el mantenimiento Almacenamiento de la máquina Servicio y reparacionesDiagrama de cableado 115V, 60 Hz 100V 50/60Hz 220 240V/50HzMáquina cortadora y preparadora de tubos de cobre 122XL Ridge Tool Company