RIDGID 122XL manual Machine Storage Service and Repair, Wiring Diagram, Motor

Page 12

122XL Copper Cutting and Prep Machine

5.Reinstall nut and washer and tighten by again holding the shaft stationary. Apply sufficient torque to the nut to prevent the disk from turning.

Machine Storage

WARNING Motor-driven equipment must be kept in- doors or well covered in rainy weather. Store the machine in a locked area that is out of reach of children and people unfamiliar with cutting machines. This machine can cause serious injury in the hands of untrained users.

Service and Repair

WARNING

Figure 11 – Assembling Deburring Disk

Motor

Motor is equipped with a thermal overload that turns off the motor in the event it develops excessive heat.

To reset the thermal overload, wait approximately 15 minutes for the motor to cool and remove the bottom cover. Press the red button located on the end of the motor opposite the reamer.

WARNING To prevent electrical shock, make sure machine is unplugged from power source before remov- ing cover.

Replace the cover and plug the machine into an elec- trical outlet. Turn the ON/OFF switch to the ON position. If motor does not start or the thermal overload continu- ally trips during normal use, the machine should be taken to an Authorized Service Center.

Service and repair work on this Copper Cutting and Prep Machine must be performed by qualified repair personnel. Machine should be taken to a RIDGID Independent Authorized Service Center or returned to the factory. All repairs made by Ridge service facilities are warranted against defects in material and workmanship.

When servicing this machine, only identical replace- ment parts should be used. Failure to follow these instructions may create a risk of electrical shock or other serious injury.

If you have any questions regarding the service or repair of this machine, call or write to:

Ridge Tool Company Technical Service Department 400 Clark Street

Elyria, Ohio 44035-6001 Tel: (800) 519-3456

E-Mail: techservices@ridgid.com

For name and address of your nearest Independent Authorized Service Center, contact the Ridge Tool Company at (800) 519-3456 or http://www.ridgid.com

Wiring Diagram

115V – 60Hz

100V – 50/60Hz

(220 – 240V/50Hz)

 

Switch

 

Black (BRN)

Back View

 

Black

 

White (BLU)

White

Motor

Green (GRN-YEL)

Green

 

 

Chassis

 

 

Ground

 

10

Ridge Tool Company

Image 12
Contents 122XL Copper Cutting and Prep Machine Table of Contents 122XL Copper Cutting and Prep Machine General Safety Information Work Area SafetyElectrical Safety Personal SafetySpecific Safety Information Description, Specifications and Standard EquipmentMachine Assembly SpecificationsAccessories Standard EquipmentMachine Inspection Machine and Work Area Set-UpMounting on No Stand Operating Instructions Cutting TubeCleaning/Deburring O.D. of Tube Turn ON/OFF switch to the OFF positionAccessories Cleaning Inside of FittingsReaming I.D. of Tube Maintenance Instructions Machine Storage Service and Repair Wiring DiagramMotor 115V 60Hz 100V 50/60Hz 220 240V/50HzMachine à couper et à préparer le cuivre modèle 122XL Table des matières Consignes générales de sécurité Sécurité du chantierSécurité électrique Sécurité individuelleService après-vente Consignes de sécurité particulièresUtilisation et entretien des outils Sécurité de la machineAccessoires Description, spécifications et équipements de baseSpécifications Equipements de baseInstallation sur trépied type Accessoire facultatifAssemblage de la machine Inspection de la machinePréparation de la machine et du chantier Utilisation de la machine Coupe des tuyauxNettoyage et ébarbage de l’extérieur du tuyau Alésage de l’intérieur des tuyauxAccessoires Nettoyage de l’intérieur des raccordsEntretien Stockage de la machine Entretien et réparationsSchéma électrique MoteurMáquina cortadora y preparadora de tubos de cobre 122XL Índice Información general de seguridad Seguridad en la zona de trabajoSeguridad eléctrica Seguridad personalInformación específica de seguridad Uso y cuidado de la máquinaServicio Seguridad de la máquinaDescripción, especificaciones y equipo estándar DescripciónEspecificaciones Equipo estándarMontaje de la máquina Revisión de la máquinaEscobillas limpiafittings y su portaescobillas Montaje en el Soporte NoPreparación de la máquina y de la zona de trabajo Instrucciones de funcionamiento Corte de tubosMueva el interruptor de ON/OFF a la posición de OFF apagado Accesorios Escariado del diámetro interior del tuboLimpieza del interior de un fitting Instrucciones para el mantenimiento Almacenamiento de la máquina Servicio y reparacionesDiagrama de cableado 115V, 60 Hz 100V 50/60Hz 220 240V/50HzMáquina cortadora y preparadora de tubos de cobre 122XL Ridge Tool Company