RIDGID 122XL manual Cleaning/Deburring O.D. of Tube, Turn ON/OFF switch to the OFF position

Page 9

122XL Copper Cutting and Prep Machine

NOTE! To adjust the height of the cutter wheel, push handle to the right and relocate position pin by moving handle up or down.

6.Lower the handle until the cutter wheel support rollers contact the tubing (Figure 4). Turn the ON/OFF switch to the ON position.

CAUTION Tubing will rotate. Keep hands away from ends of tubing that may have burrs or sharp edges.

Figure 4 – Cutter Wheel Support Rollers Contacting Tubing

7.Apply pressure to the handle slowly and continu- ously until the tubing is cut. Do not force the cutter wheel into the workpiece. This will damage and short- en the life of the cutter wheel.

8.Release pressure from the handle but still have the cutter wheel support rollers maintain contact with the tubing (Figure 5). The rollers will hold the tubing so it will not fall to the ground.

9.Turn the ON/OFF switch to the OFF position.

10.Remove tubing from the machine. Raise the cutter handle to its maximum height.

Cleaning/Deburring O.D. of Tube

1.Turn the ON/OFF switch to the ON position.

2.Place the end of the tube on the rest plate. Lengths of tubing longer than four feet should be supported by pipe stands.

WARNING Pipe supports are needed to maintain control of the workpiece.

3.Press tube gently against the brush and rotate slow- ly until surface is bright (Figure 6).

WARNING Keep hands away from rotating parts.

4.Remove external burrs by rotating tube against debur- ring cutter (Figure 7). This action also bevels the end of tube for easier insertion into the fitting.

Figure 6 – Cleaning O.D. of Tube

 

 

Figure 7 – Deburring O.D. of Tube

 

Figure 5 – Cutter Wheel Support Rollers Holding Tubing

5. Turn ON/OFF switch to the OFF position.

 

After Cut

 

 

 

 

 

 

 

 

 

Ridge Tool Company

7

Image 9
Contents 122XL Copper Cutting and Prep Machine Table of Contents 122XL Copper Cutting and Prep Machine Work Area Safety General Safety InformationElectrical Safety Personal SafetyDescription, Specifications and Standard Equipment Specific Safety InformationSpecifications Machine AssemblyAccessories Standard EquipmentMachine Inspection Machine and Work Area Set-UpMounting on No Stand Cutting Tube Operating InstructionsTurn ON/OFF switch to the OFF position Cleaning/Deburring O.D. of TubeAccessories Cleaning Inside of FittingsReaming I.D. of Tube Maintenance Instructions Wiring Diagram Machine Storage Service and RepairMotor 115V 60Hz 100V 50/60Hz 220 240V/50HzMachine à couper et à préparer le cuivre modèle 122XL Table des matières Sécurité du chantier Consignes générales de sécuritéSécurité électrique Sécurité individuelleConsignes de sécurité particulières Service après-venteUtilisation et entretien des outils Sécurité de la machineDescription, spécifications et équipements de base AccessoiresSpécifications Equipements de baseAccessoire facultatif Installation sur trépied typeAssemblage de la machine Inspection de la machinePréparation de la machine et du chantier Coupe des tuyaux Utilisation de la machineAlésage de l’intérieur des tuyaux Nettoyage et ébarbage de l’extérieur du tuyauNettoyage de l’intérieur des raccords AccessoiresEntretien Entretien et réparations Stockage de la machineSchéma électrique MoteurMáquina cortadora y preparadora de tubos de cobre 122XL Índice Seguridad en la zona de trabajo Información general de seguridadSeguridad eléctrica Seguridad personalUso y cuidado de la máquina Información específica de seguridadServicio Seguridad de la máquinaDescripción Descripción, especificaciones y equipo estándarEspecificaciones Equipo estándarRevisión de la máquina Montaje de la máquinaEscobillas limpiafittings y su portaescobillas Montaje en el Soporte NoPreparación de la máquina y de la zona de trabajo Corte de tubos Instrucciones de funcionamientoMueva el interruptor de ON/OFF a la posición de OFF apagado Accesorios Escariado del diámetro interior del tuboLimpieza del interior de un fitting Instrucciones para el mantenimiento Servicio y reparaciones Almacenamiento de la máquina115V, 60 Hz 100V 50/60Hz 220 240V/50Hz Diagrama de cableadoMáquina cortadora y preparadora de tubos de cobre 122XL Ridge Tool Company