Southbend SB1021, SB1022 manual Machine Labels, PSBLABEL13VS Door Injury Hazard Label

Page 62

Model SB1021/SB1022

P A R T S

For Machines Mfg. Since 8/09

Machine Labels

600

608609

607

603

606

605

610

REF	PART #	DESCRIPTION
600	PSB1021600	MACHINE ID LABEL (SB1021)
600	PSB1022600	MACHINE ID LABEL (SB1022)
601	PSB1021601	UNSTABLE W/P HAZARD LABEL
602	PSBLABEL02VS	DISCONNECT WARNING LABEL
603	PSBLABEL15M	ELECTRICITY LABEL
604	PSB1021604	CUTTING HAZARD LABEL
605	PSB1021605	SPEED LABEL

602

601

603

604

611

602

REF	PART #	DESCRIPTION
606	PSB1021606	SPEED CHANGE NOTICE LABEL
607	PSBLABEL03VL	EYE INJURY HAZARD LABEL
608	PSBLABEL01VL	READ MANUAL LABEL
609	PSBLABEL13VS	DOOR INJURY HAZARD LABEL
610	PSB1021610	SOUTH BEND GRAY TOUCH-UP PAINT
611	PSB1021611	MODEL NUMBER LABEL (SB1021)
611	PSB1022611	MODEL NUMBER LABEL (SB1022)

The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at (360) 734-1540 or www.southbendlathe.com to order new labels.

-60-

Image 62

Contents Metal Cutting Bandsaw Scope of Manual UpdatesCustomer Service Manual FeedbackTable of Contents Capabilities FeaturesAbout This Machine Identiﬁcation Oper ationMachine Speciﬁcations Machine SpeciﬁcationsCutting Capacity 220V, 3-Phase Wheel Bearings Shielded and Permanently Lubricated Basic Machine Safety Understanding Risks of MachineryF E T Y Additional Metal Cutting Bandsaw Safety Unpacking Preparation OverviewThings Youll Need Basic steps for removing rust preventative Cleaning & ProtectingBefore cleaning, gather the following Location Leveling Lifting & MovingLeveling & Mounting Initial Lubrication AssemblyInspections Adjustments Bolting to Concrete FloorsSB1021 220V Power Source Power ConnectionSB1021 110V Prewired Power Source SB1022 220V 3-Phase Power SourceTest Run To test run your machineOperation Overview Controls Variable speed handwheelBlade Length Blade SelectionBlade Terminology Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchTo replace the blade Blade ChangesBlade Tensioning To correctly tension the bladeBlade Care Blade BreakageBlade Care & Break-In Blade Break-InBlade Speed Chart Chip Inspection ChartPositioning Guide Post Adjusting Blade GuidesTo properly adjust the upper and lower blade guides To properly position the guide post⁄16 To tilt the table left or right Tilting TableBlade Welding To tilt the table forward or backwardAbove 3⁄8 Blade ⁄4-3⁄8 Blade Correct Not Correct Correct Not Correct Cut and reweld Dressing Grinding Wheel Maintenance ScheduleCleaning Lubrication Upper wheel leadscrew lubricationTo check/tension/replace the V-belts BeltsDressing Rubber Tires To redress the rubber tiresTable Calibration To adjust the upper wheel for blade trackingBlade Tracking To calibrate the table to zeroGuide Post Alignment To align the guide postLeadscrew End Play To adjust the lead screw collars to reduce backlashPinion Gear Backlash To reduce the pinion gear backlashTroubleshooting Symptom Possible Cause Possible SolutionBlade Selection section beginning on Dull blade missing teeth Replace blade Troubleshooting Electrical Safety Instructions Wiring Overview Wiring Diagram Color KEYSB1021/2 Control Panel & Welding Unit Welding UnitSB1021 110V Electrical Panel, Motor & Cord Electrical PanelSB1021 220V Electrical Panel, Motor & Cord SB1022 220V Electrical Panel, Motor & Cord Welding Panel Power Transformer Electrical Component PicturesLower Frame Lower Frame Parts List Drive System Drive System Parts List PCAP40MUpper Frame Upper Frame Parts List Table & Tensioning System Table & Tensioning System Parts List Electrical Cabinet Cabinet DoorWelder Welder & Control Panel Breakdown Machine Labels PSBLABEL13VS Door Injury Hazard LabelWarranty #TRCRBLTSJB12079