Woodstock M1109 owner manual Tailstock adjustment option #2

Page 23

M1109 Combo Lathe/Mill

5.Place the live center in the tailstock.

6.Attach a lathe/mill dog to the bar stock and mount it between centers.

7.Turn approximately 0.010" off the diameter.

8.Measure the stock with a micrometer.

If the stock diameter is thicker at the tailstock end, the tailstock needs to be moved toward you half the distance of the amount of the taper (see

Figure 28).

If the stock diameter is thinner at the tailstock end, the tailstock needs to be moved away from you half the distance of the amount of the taper (see Figure 29).

9.Mount a dial indicator so the dial plunger is on the tailstock barrel before making adjustments to the tailstock.

10.Turn another 0.010" off of the diameter and check for a taper. Repeat this process as necessary until the desired amount of accuracy is achieved.

Figure 28. Tailstock adjustment option #1.

Figure 29. Tailstock adjustment option #2.

OPERATIONS

-21-

Image 23
Contents Combo LATHE/MILL Page Contents Parts Woodstock Technical Support SpecificationsIntroduction Controls and Features Standard Safety Instructions SafetySafety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential InjuriesGrounding Electrical220V Operation Extension CordsInventory SetupInstalled Accessories Figure Qty Packaged Accessories FigureMachine Placement Cleaning MachineTo unpack and move the lathe/mill, do these steps Uncrating and LiftingTest Run and Break-In To begin the test run procedure, do these stepsTroubleshooting on General Power SupplyLathe Operations Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILLTo remove a set of jaws, do these steps Replacing JawsClamping workpiece Using the Four-Jaw ChuckFaceplate installed Using the FaceplateTo use the tailstock, do these steps Using the TailstockTo install the MT#3 drill chuck, do these steps Drilling with the TailstockTo align the tailstock, do these steps To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock Tailstock AlignmentTailstock adjustment option #2 To install a dead or live center, do these steps Using CentersTo use the steady rest, do these steps Using the Steady RestUsing the Follow Rest To set the angular position, do these steps Setting Compound SlideUsing the Tool Post Longitudinal Handwheel Using Manual FeedCutting Speeds for High Speed Steel HSS Cutting Tools Setting RPMTo determine and set the needed cutting RPM, do these steps Refer to the Change Gear Chart on Page 29, or Setting Power Feed RateLoosen the apron lock bolt and use the feed lever Figure Threading SetupTo setup for threading, do these steps Change Gear Chart Removing Tools Installing ToolsTo install a tool in the spindle, do these steps Milling OperationsTo use the quill, do these steps Headstock PositioningQuill Travel To position the spindle head vertically, do these stepsTable Travel To begin the start up procedure, do these stepsHigh speed steel cutting chart General Lubrication MaintenanceGeneral Maintenance General CleaningTo replace or adjust the V-belts, do these steps Adjusting/Replacing the V-BeltCross Slide Backlash ServiceCross Slide, Half-Nut Compound Slide Gib Adjustments M1109 Electrical panel Electrical Component and Connection IndexContactor Electrical ConnectionsTransformer connection Lathe controls Wiring DiagramMotor & Electrical TroubleshootingOperation and Work Results Parts Diagram PART# Description Series Parts List1007 1028 Thread Dial DiagramSPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA