Woodstock M1109 owner manual Table Travel, To begin the start up procedure, do these steps

Page 34

M1109 Combo Lathe/Mill

OPERATIONS

Table Travel

The mill table of the Model M1109 can be moved in two axes—cross feed and longitudinal feed. Each of these axes are controlled by graduated handwheels to accurately position the workpiece in relation to the tool. To set the power feed for milling, refer to Setting Power Feed Rate on Page 27.

Cross Feed

The cross feed is controlled by the cross feed handwheel of the lathe shown in Figure 50.

Longitudinal Feed Control

The longitudinal feed is controlled by the longitudinal handwheel of the lathe, and the lock at the back of the saddle (see Figure 50).

Start Up and Spindle Break-in Procedures

It is essential to closely follow the proper break-in pro- cedures to ensure trouble free performance. Complete this process once you have familiarized yourself with all instructions in this manual.

To begin the start up procedure, do these steps:

1.Make sure the mill has been properly lubricated.

2.Make sure there are no obstructions around or underneath the spindle.

3.Set the spindle speed to 240 RPM.

4. Turn the mill ON (Figure 51).

5.Turn the spindle ON and run it a minimum of 10 minutes. Repeat this step on the other three RPM ranges.

NOTICE

Failure to follow start up and spindle break-in pro- cedures will cause rapid deterioration of spindle and other related parts, and never shift gears while lathe or mill is running.

Leadscrew Lever

Feed

Lever

Figure 50. Headstock and apron controls.

Mill Spindle

ON/OFF Switch

Figure 51. Start switch location.

Milling Speed

Levers

Figure 52. Gearbox and controls.

-32-

Image 34

Contents Combo LATHE/MILL Page Contents Parts Introduction SpecificationsWoodstock Technical Support Controls and Features Safety Standard Safety InstructionsSafety Additional Safety Instructions for Lathe/Mills Avoiding Potential Injuries Always protect the bed ways,Extension Cords Electrical220V Operation GroundingPackaged Accessories Figure SetupInstalled Accessories Figure Qty InventoryCleaning Machine Machine PlacementUncrating and Lifting To unpack and move the lathe/mill, do these stepsTroubleshooting on To begin the test run procedure, do these stepsTest Run and Break-In Lathe Operations Power SupplyGeneral Disconnect Power to the LATHE/MILL Chuck and Faceplate MountingReplacing Jaws To remove a set of jaws, do these stepsUsing the Four-Jaw Chuck Clamping workpieceUsing the Faceplate Faceplate installedDrilling with the Tailstock Using the TailstockTo install the MT#3 drill chuck, do these steps To use the tailstock, do these stepsTailstock Alignment To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock To align the tailstock, do these stepsTailstock adjustment option #2 Using Centers To install a dead or live center, do these stepsUsing the Follow Rest Using the Steady RestTo use the steady rest, do these steps Using the Tool Post Setting Compound SlideTo set the angular position, do these steps Using Manual Feed Longitudinal HandwheelTo determine and set the needed cutting RPM, do these steps Setting RPMCutting Speeds for High Speed Steel HSS Cutting Tools Setting Power Feed Rate Refer to the Change Gear Chart on Page 29, orTo setup for threading, do these steps Threading SetupLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart Milling Operations Installing ToolsTo install a tool in the spindle, do these steps Removing ToolsTo position the spindle head vertically, do these steps Headstock PositioningQuill Travel To use the quill, do these stepsTo begin the start up procedure, do these steps Table TravelHigh speed steel cutting chart General Cleaning MaintenanceGeneral Maintenance General LubricationAdjusting/Replacing the V-Belt To replace or adjust the V-belts, do these stepsCross Slide, Half-Nut Compound Slide Gib Adjustments ServiceCross Slide Backlash Electrical Component and Connection Index M1109 Electrical panelElectrical Connections ContactorTransformer connection Wiring Diagram Lathe controlsTroubleshooting Motor & ElectricalOperation and Work Results Parts Diagram Series Parts List PART# DescriptionThread Dial Diagram 1007 1028SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA