Woodstock M1109 owner manual Pinnedknob

Page 57

M1109 Combo Lathe/Mill

3500 Series Parts List

REF	PART�#	DESCRIPTION
3501	XM11093501	PINNED�KNOB
3502	XM11093502	ADJUSTMENT�STUD
3503	XM11093503	TAPERED�PIN
3504	XM11093504	BRASS-TIPPED�FINGER
3505	XM11093505	SPECIAL�SET�SCREW�M6-1
3506	XPN01M	HEX�NUT�M6-1
3507	XM11093507	THUMB�KNOB�M6-1.0�X�20
3508	XM11093508	CLEVIS�PIN�8�X�32MM
3509	XM11093509	COTTER�PIN�3�X�25MM
3510	XM11093510	STEADY�REST�HEAD
3511	XPW01M	FLAT�WASHER�8MM
3512	XM11093512	STEADY�REST�BASE
3513	XM11093513	FEMALE�KNOB�M8-1.25

REF	PART�#	DESCRIPTION
3514	XM11093514	SPECIAL�EYE�BOLT
3515	XPW04M	FLAT�WASHER�10MM
3516	XPN02M	HEX�NUT�M10-1.5
3517	XM11093517	CHOCK
3518	XPB120M	HEX�BOLT�M10-1.5�X�65
3519	XPSB14M	CAP�SCREW�M8-1.25�X�20
3520	XPSB31M	CAP�SCREW�M8-1.25�X�25
3521	XM11093521	FOLLOW�REST�CASTING
3522	XM11093522	COMPLETE�FOLLOW�REST
3523	XM11093523	COMPLETE�STEADY�REST
3524	XPW03M	FLAT�WASHER�6MM
3525	XM11093525	CLEVIS�PIN�6�X�32MM

PARTS

-55-

Image 57

Contents Combo LATHE/MILL Page Contents Parts Specifications IntroductionWoodstock Technical Support Controls and Features Standard Safety Instructions SafetySafety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential Injuries220V Operation ElectricalExtension Cords GroundingInstalled Accessories Figure Qty SetupPackaged Accessories Figure InventoryMachine Placement Cleaning MachineTo unpack and move the lathe/mill, do these steps Uncrating and LiftingTo begin the test run procedure, do these steps Troubleshooting onTest Run and Break-In Power Supply Lathe OperationsGeneral Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILLTo remove a set of jaws, do these steps Replacing JawsClamping workpiece Using the Four-Jaw ChuckFaceplate installed Using the FaceplateTo install the MT#3 drill chuck, do these steps Using the TailstockDrilling with the Tailstock To use the tailstock, do these stepsCutting Shallow Tapers With the Tailstock To setup the tailstock to cut tapers, do these stepsTailstock Alignment To align the tailstock, do these stepsTailstock adjustment option #2 To install a dead or live center, do these steps Using CentersUsing the Steady Rest Using the Follow RestTo use the steady rest, do these steps Setting Compound Slide Using the Tool PostTo set the angular position, do these steps Longitudinal Handwheel Using Manual FeedSetting RPM To determine and set the needed cutting RPM, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools Refer to the Change Gear Chart on Page 29, or Setting Power Feed RateThreading Setup To setup for threading, do these stepsLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart To install a tool in the spindle, do these steps Installing ToolsMilling Operations Removing ToolsQuill Travel Headstock PositioningTo position the spindle head vertically, do these steps To use the quill, do these stepsTable Travel To begin the start up procedure, do these stepsHigh speed steel cutting chart General Maintenance MaintenanceGeneral Cleaning General LubricationTo replace or adjust the V-belts, do these steps Adjusting/Replacing the V-BeltService Cross Slide, Half-Nut Compound Slide Gib AdjustmentsCross Slide Backlash M1109 Electrical panel Electrical Component and Connection IndexContactor Electrical ConnectionsTransformer connection Lathe controls Wiring DiagramMotor & Electrical TroubleshootingOperation and Work Results Parts Diagram PART# Description Series Parts List1007 1028 Thread Dial DiagramSPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA