Woodstock M1109 owner manual Thread Dial Diagram, 1007 1028

Page 48

PARTS

1030
1007
1028
1026	1027
1024	1025
1022	1023
1020	1021
1019
	1018
1017		1015 1016
1017		1015 1016
	1014
	1013
1012	1008	1009 1010 1011
1007
	1006
1005 1001 1002		1003 1004

M1109 Combo Lathe/Mill

Thread Dial Diagram

(1000 Series Parts)

	1062	1007	1060		1059
1051 1007		1049			1058		1057					1007	1064 1065 1066 1067 1068			1069	1070
1051 1007		1048	1047		1046			1056	1055 1054		1053		1064 1065 1066 1067 1068			1069	1070	1091 1080	1081	10071088	1085108710831089
1039	1038	1037 1036		1035		1034		1032	1031	1041		1040	1052 1071	1072	1073	1075	1077	1091 1080	1081	10071088	1085108710831089
							1045		1042							1078		1079
								1044	1042							1078		1079
									1043
								1033							1074	1007				10841082
																		1090
													1100 1101					1092 1093 1094 1007		6
																				1-
															1102					6	1097
															1102					10	1097
																				9
																				9
																				10
																				10071098	1099
																				1105	1104
																				1107	1106
																				1108
																				1110	1109
																				1110	1111

-46-

Image 48

Contents Combo LATHE/MILL Page Contents Parts Specifications IntroductionWoodstock Technical Support Controls and Features Safety Standard Safety InstructionsSafety Additional Safety Instructions for Lathe/Mills Avoiding Potential Injuries Always protect the bed ways,Electrical 220V OperationExtension Cords GroundingSetup Installed Accessories Figure QtyPackaged Accessories Figure InventoryCleaning Machine Machine PlacementUncrating and Lifting To unpack and move the lathe/mill, do these stepsTo begin the test run procedure, do these steps Troubleshooting onTest Run and Break-In Power Supply Lathe OperationsGeneral Disconnect Power to the LATHE/MILL Chuck and Faceplate MountingReplacing Jaws To remove a set of jaws, do these stepsUsing the Four-Jaw Chuck Clamping workpieceUsing the Faceplate Faceplate installedUsing the Tailstock To install the MT#3 drill chuck, do these stepsDrilling with the Tailstock To use the tailstock, do these stepsTo setup the tailstock to cut tapers, do these steps Cutting Shallow Tapers With the TailstockTailstock Alignment To align the tailstock, do these stepsTailstock adjustment option #2 Using Centers To install a dead or live center, do these stepsUsing the Steady Rest Using the Follow RestTo use the steady rest, do these steps Setting Compound Slide Using the Tool PostTo set the angular position, do these steps Using Manual Feed Longitudinal HandwheelSetting RPM To determine and set the needed cutting RPM, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools Setting Power Feed Rate Refer to the Change Gear Chart on Page 29, orThreading Setup To setup for threading, do these stepsLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart Installing Tools To install a tool in the spindle, do these stepsMilling Operations Removing ToolsHeadstock Positioning Quill TravelTo position the spindle head vertically, do these steps To use the quill, do these stepsTo begin the start up procedure, do these steps Table TravelHigh speed steel cutting chart Maintenance General MaintenanceGeneral Cleaning General LubricationAdjusting/Replacing the V-Belt To replace or adjust the V-belts, do these stepsService Cross Slide, Half-Nut Compound Slide Gib AdjustmentsCross Slide Backlash Electrical Component and Connection Index M1109 Electrical panelElectrical Connections ContactorTransformer connection Wiring Diagram Lathe controlsTroubleshooting Motor & ElectricalOperation and Work Results Parts Diagram Series Parts List PART# DescriptionThread Dial Diagram 1007 1028SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA