Woodstock M1109 owner manual Accessories and Labels Diagram

Page 66

M1109 Combo Lathe/Mill

Accessories and Labels Diagram

(8000 Series Parts)

8004

8016

PARTS

8009

8017

8006

8015

8008

8042

8021

8011

8039

8040

8041

8038

8037 8034

8032

8030

8028

8010

8033

	8013	8020
		8014
	8005	8018
	8005
		8012
		8048
8022	8007
	8047
8001	8046
8001	8045
	8045
		8023
	8044

8024

	8025
	8026
	8043
	8027
8036	8035
8036	8031
	8031	8029
		8029

-64-

Image 66

Contents Combo LATHE/MILL Page Contents Parts Specifications IntroductionWoodstock Technical Support Controls and Features Safety Standard Safety InstructionsSafety Additional Safety Instructions for Lathe/Mills Avoiding Potential Injuries Always protect the bed ways,Extension Cords Electrical220V Operation GroundingPackaged Accessories Figure SetupInstalled Accessories Figure Qty InventoryCleaning Machine Machine PlacementUncrating and Lifting To unpack and move the lathe/mill, do these stepsTo begin the test run procedure, do these steps Troubleshooting onTest Run and Break-In Power Supply Lathe OperationsGeneral Disconnect Power to the LATHE/MILL Chuck and Faceplate MountingReplacing Jaws To remove a set of jaws, do these stepsUsing the Four-Jaw Chuck Clamping workpieceUsing the Faceplate Faceplate installedDrilling with the Tailstock Using the TailstockTo install the MT#3 drill chuck, do these steps To use the tailstock, do these stepsTailstock Alignment To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock To align the tailstock, do these stepsTailstock adjustment option #2 Using Centers To install a dead or live center, do these stepsUsing the Steady Rest Using the Follow RestTo use the steady rest, do these steps Setting Compound Slide Using the Tool PostTo set the angular position, do these steps Using Manual Feed Longitudinal HandwheelSetting RPM To determine and set the needed cutting RPM, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools Setting Power Feed Rate Refer to the Change Gear Chart on Page 29, orThreading Setup To setup for threading, do these stepsLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart Milling Operations Installing ToolsTo install a tool in the spindle, do these steps Removing ToolsTo position the spindle head vertically, do these steps Headstock PositioningQuill Travel To use the quill, do these stepsTo begin the start up procedure, do these steps Table TravelHigh speed steel cutting chart General Cleaning MaintenanceGeneral Maintenance General LubricationAdjusting/Replacing the V-Belt To replace or adjust the V-belts, do these stepsService Cross Slide, Half-Nut Compound Slide Gib AdjustmentsCross Slide Backlash Electrical Component and Connection Index M1109 Electrical panelElectrical Connections ContactorTransformer connection Wiring Diagram Lathe controlsTroubleshooting Motor & ElectricalOperation and Work Results Parts Diagram Series Parts List PART# DescriptionThread Dial Diagram 1007 1028SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA