Woodstock M1109 owner manual Introduction, Woodstock Technical Support, Specifications

Page 5

M1109 Combo Lathe/Mill

INTRODUCTION

Woodstock Technical Support

Your new SHOP FOX® Model M1109 Combo Lathe/Mill has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.

Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product.

We stand behind our machines! In the event that questions arise about your machine, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox. biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.

If you need the latest edition of this manual, you can download it from http://www.shopfox.biz. If you have comments about this manual, please contact us at:

Woodstock International, Inc.

Attn: Technical Documentation Manager

P.O. Box 2309

Bellingham, WA 98227

Specifications

Milling Motor		3⁄4" HP, 220V, 7 Amps, Single-Phase, TEFC
Lathe Motor		11⁄2" HP, 220V, 10 Amps, Single-Phase, TEFC
Lathe Swing Over Bed		121⁄2"
Mill/Drill Swing		141⁄2"
Mill/Drill Spindle to Worktable Capacity		...................................................171⁄4"
Distance Between Centers		291⁄2"
Spindle Bore		11⁄2"
Lathe Spindle Taper		MT #5
Mill/Drill Spindle Taper		R8, 7⁄16"-20 TPI
Tailstock Taper		MT #3
Tailstock Barrel Travel		315⁄16"
Cross Slide Travel		61⁄4"
Number of Mill/Drill Speeds		4
Mill/Drill Speed Range		240, 600, 1100, 2700 RPM
Tilting Headstock		90° L & R
Number of Lathe Speeds		12
Lathe Speeds	75, 110, 140, 200, 240, 350, 420, 600, 720, 1050, 1250, 1900 RPM
Thread Range (inches)		27 @ 8 - 120 TPI
Thread Range (metric)		18 @ 0.2 - 3.0 mm
4-Jaw Chuck		8"
3-Jaw Chuck		w/Int. & Ext. Jaws, 6"
Drill Chuck		1-13mm JT-33
Faceplate		8"
Tool Holder		4-Way Turret Tool Post
Change Gears		Steel
Dead Centers		MT5 & MT3
Approximate Net Weight		1200 lbs.
		-3-

INTRODUCTION

Image 5

Contents Combo LATHE/MILL Page Contents Parts Woodstock Technical Support SpecificationsIntroduction Controls and Features Standard Safety Instructions SafetySafety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential Injuries220V Operation ElectricalExtension Cords GroundingInstalled Accessories Figure Qty SetupPackaged Accessories Figure InventoryMachine Placement Cleaning MachineTo unpack and move the lathe/mill, do these steps Uncrating and LiftingTest Run and Break-In To begin the test run procedure, do these stepsTroubleshooting on General Power SupplyLathe Operations Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILLTo remove a set of jaws, do these steps Replacing JawsClamping workpiece Using the Four-Jaw ChuckFaceplate installed Using the FaceplateTo install the MT#3 drill chuck, do these steps Using the TailstockDrilling with the Tailstock To use the tailstock, do these stepsCutting Shallow Tapers With the Tailstock To setup the tailstock to cut tapers, do these stepsTailstock Alignment To align the tailstock, do these stepsTailstock adjustment option #2 To install a dead or live center, do these steps Using CentersTo use the steady rest, do these steps Using the Steady RestUsing the Follow Rest To set the angular position, do these steps Setting Compound SlideUsing the Tool Post Longitudinal Handwheel Using Manual FeedCutting Speeds for High Speed Steel HSS Cutting Tools Setting RPMTo determine and set the needed cutting RPM, do these steps Refer to the Change Gear Chart on Page 29, or Setting Power Feed RateLoosen the apron lock bolt and use the feed lever Figure Threading SetupTo setup for threading, do these steps Change Gear Chart To install a tool in the spindle, do these steps Installing ToolsMilling Operations Removing ToolsQuill Travel Headstock PositioningTo position the spindle head vertically, do these steps To use the quill, do these stepsTable Travel To begin the start up procedure, do these stepsHigh speed steel cutting chart General Maintenance MaintenanceGeneral Cleaning General LubricationTo replace or adjust the V-belts, do these steps Adjusting/Replacing the V-BeltCross Slide Backlash ServiceCross Slide, Half-Nut Compound Slide Gib Adjustments M1109 Electrical panel Electrical Component and Connection IndexContactor Electrical ConnectionsTransformer connection Lathe controls Wiring DiagramMotor & Electrical TroubleshootingOperation and Work Results Parts Diagram PART# Description Series Parts List1007 1028 Thread Dial DiagramSPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA