Woodstock M1109 owner manual Using Manual Feed, Longitudinal Handwheel

Page 27

M1109 Combo Lathe/Mill

Using Manual Feed

You can manually move the cutting tool around the lathe/ mill with the three handwheels shown in Figure 36.

Longitudinal Handwheel

The longitudinal handwheel moves the carriage left or right along the bed. This control is helpful when setting up the machine for turning or when manual movement is desired during turning operations.

Cross Feed Handwheel

The cross slide handwheel moves the top slide toward and away from the work. Turning the dial clockwise moves the slide toward the workpiece.

Compound Slide Handwheel

Compound

Slide

Handwheel

Cross Feed

Handwheel

Longitudinal

Handwheel

Figure 36. Carriage controls.

The compound slide handwheel controls the position of the cutting tool relative to the workpiece. The graduated dial is adjustable using the same method as the dial on the cross slide. Angle adjustment is held by two hex nuts on the base of the compound slide.

OPERATIONS

-25-

Image 27

Contents Combo LATHE/MILL Page Contents Parts Specifications IntroductionWoodstock Technical Support Controls and Features Standard Safety Instructions SafetySafety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential InjuriesGrounding Electrical220V Operation Extension CordsInventory SetupInstalled Accessories Figure Qty Packaged Accessories FigureMachine Placement Cleaning MachineTo unpack and move the lathe/mill, do these steps Uncrating and LiftingTo begin the test run procedure, do these steps Troubleshooting onTest Run and Break-In Power Supply Lathe OperationsGeneral Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILLTo remove a set of jaws, do these steps Replacing JawsClamping workpiece Using the Four-Jaw ChuckFaceplate installed Using the FaceplateTo use the tailstock, do these steps Using the TailstockTo install the MT#3 drill chuck, do these steps Drilling with the TailstockTo align the tailstock, do these steps To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock Tailstock AlignmentTailstock adjustment option #2 To install a dead or live center, do these steps Using CentersUsing the Steady Rest Using the Follow RestTo use the steady rest, do these steps Setting Compound Slide Using the Tool PostTo set the angular position, do these steps Longitudinal Handwheel Using Manual FeedSetting RPM To determine and set the needed cutting RPM, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools Refer to the Change Gear Chart on Page 29, or Setting Power Feed RateThreading Setup To setup for threading, do these stepsLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart Removing Tools Installing ToolsTo install a tool in the spindle, do these steps Milling OperationsTo use the quill, do these steps Headstock PositioningQuill Travel To position the spindle head vertically, do these stepsTable Travel To begin the start up procedure, do these stepsHigh speed steel cutting chart General Lubrication MaintenanceGeneral Maintenance General CleaningTo replace or adjust the V-belts, do these steps Adjusting/Replacing the V-BeltService Cross Slide, Half-Nut Compound Slide Gib AdjustmentsCross Slide Backlash M1109 Electrical panel Electrical Component and Connection IndexContactor Electrical ConnectionsTransformer connection Lathe controls Wiring DiagramMotor & Electrical TroubleshootingOperation and Work Results Parts Diagram PART# Description Series Parts List1007 1028 Thread Dial DiagramSPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA