Woodstock M1109 owner manual Using the Tailstock, Drilling with the Tailstock

Page 21

M1109 Combo Lathe/Mill

Using the Tailstock

The tailstock (Figure 23) can be used to support workpieces with the use of a live or dead center. Using an MT#3 drill chuck and a drill bit, the lathe can drill or bore holes in the center of a part. The tailstock can also be offset for cutting shallow tapers.

To use the tailstock, do these steps:

1.Slide the tailstock to the desired position.

2.Pull up on the tailstock lock lever to lock the tailstock in place on the ways.

3.With the tailstock locked, push down the quill lock lever to unlock.

4.Turn the quill feed handle clockwise to feed/move the quill towards the spindle, or counterclockwise to move away from the spindle.

5.Turn the quill lock lever to lock the quill in place.

Quill Feed	Quill Lock Lever
Tailstock Lock Lever
	Offset
	Adjustment
Offset
Scale

Figure 23. Tailstock and quill lock handles

in locked position.

Drilling with the Tailstock

To install the MT#3 drill chuck, do these steps:

1.With the tailstock locked, unlock the quill lock lever.

2.Turn the quill feed handle clockwise to extend the quill about one inch.

3.Insert the MT#3 chuck (Figure 24) or an MT#3 tapered drill shank into the quill until the taper is firmly seated.

4.Turn the quill feed handle clockwise to feed the drill bit into a rotating workpiece.

	5. To remove the chuck taper, turn the quill feed han-
	5. To remove the chuck taper, turn the quill feed han-	Figure 24. Setting up tailstock for drilling.
	dle counterclockwise until the chuck is pushed out of	Figure 24. Setting up tailstock for drilling.
	dle counterclockwise until the chuck is pushed out of
	the tailstock taper.

-19-

OPERATIONS

Image 21

Contents Combo LATHE/MILL Page Contents Parts Specifications IntroductionWoodstock Technical Support Controls and Features Standard Safety Instructions SafetySafety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential Injuries220V Operation ElectricalExtension Cords GroundingInstalled Accessories Figure Qty SetupPackaged Accessories Figure InventoryMachine Placement Cleaning MachineTo unpack and move the lathe/mill, do these steps Uncrating and LiftingTo begin the test run procedure, do these steps Troubleshooting onTest Run and Break-In Power Supply Lathe OperationsGeneral Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILLTo remove a set of jaws, do these steps Replacing JawsClamping workpiece Using the Four-Jaw ChuckFaceplate installed Using the FaceplateTo install the MT#3 drill chuck, do these steps Using the TailstockDrilling with the Tailstock To use the tailstock, do these stepsCutting Shallow Tapers With the Tailstock To setup the tailstock to cut tapers, do these stepsTailstock Alignment To align the tailstock, do these stepsTailstock adjustment option #2 To install a dead or live center, do these steps Using CentersUsing the Steady Rest Using the Follow RestTo use the steady rest, do these steps Setting Compound Slide Using the Tool PostTo set the angular position, do these steps Longitudinal Handwheel Using Manual FeedSetting RPM To determine and set the needed cutting RPM, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools Refer to the Change Gear Chart on Page 29, or Setting Power Feed RateThreading Setup To setup for threading, do these stepsLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart To install a tool in the spindle, do these steps Installing ToolsMilling Operations Removing ToolsQuill Travel Headstock PositioningTo position the spindle head vertically, do these steps To use the quill, do these stepsTable Travel To begin the start up procedure, do these stepsHigh speed steel cutting chart General Maintenance MaintenanceGeneral Cleaning General LubricationTo replace or adjust the V-belts, do these steps Adjusting/Replacing the V-BeltService Cross Slide, Half-Nut Compound Slide Gib AdjustmentsCross Slide Backlash M1109 Electrical panel Electrical Component and Connection IndexContactor Electrical ConnectionsTransformer connection Lathe controls Wiring DiagramMotor & Electrical TroubleshootingOperation and Work Results Parts Diagram PART# Description Series Parts List1007 1028 Thread Dial DiagramSPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA