Woodstock M1109 owner manual Leadscrew Gearbox Diagram 2000 Series Parts

Page 50

PARTS

								2019	2020
							2009 2010		2020
						2008	2009 2010
				2006	2007		2018
				2006	2007		2017
				2005			2017
			2003	2004			2016
			2003
	2001	2002					2015
	2001						2014
							2014
							2013
						2012
				2011			2027
				2011
									2029
							2023	2028
							2023
							2026
							2025
	2051						2024
	2051
2050							2022
-							2021
48							2021		2030
-									2030
-
2049
									2031
					2035				2032
									2032
							2036
							2037		2033
							2038		2033
		2046 2045	2044	2043			2038
2048	2047	2046 2045	2044	2043			2039
							2040		2034
							2041
							2042

Leadscrew Gearbox Diagram (2000 Series Parts)

M1109 Combo Lathe/Mill

Image 50

Contents Combo LATHE/MILL Page Contents Parts Woodstock Technical Support SpecificationsIntroduction Controls and Features Safety Standard Safety InstructionsSafety Additional Safety Instructions for Lathe/Mills Avoiding Potential Injuries Always protect the bed ways,Extension Cords Electrical220V Operation GroundingPackaged Accessories Figure SetupInstalled Accessories Figure Qty InventoryCleaning Machine Machine PlacementUncrating and Lifting To unpack and move the lathe/mill, do these stepsTest Run and Break-In To begin the test run procedure, do these stepsTroubleshooting on General Power SupplyLathe Operations Disconnect Power to the LATHE/MILL Chuck and Faceplate MountingReplacing Jaws To remove a set of jaws, do these stepsUsing the Four-Jaw Chuck Clamping workpieceUsing the Faceplate Faceplate installedDrilling with the Tailstock Using the TailstockTo install the MT#3 drill chuck, do these steps To use the tailstock, do these stepsTailstock Alignment To setup the tailstock to cut tapers, do these stepsCutting Shallow Tapers With the Tailstock To align the tailstock, do these stepsTailstock adjustment option #2 Using Centers To install a dead or live center, do these stepsTo use the steady rest, do these steps Using the Steady RestUsing the Follow Rest To set the angular position, do these steps Setting Compound SlideUsing the Tool Post Using Manual Feed Longitudinal HandwheelCutting Speeds for High Speed Steel HSS Cutting Tools Setting RPMTo determine and set the needed cutting RPM, do these steps Setting Power Feed Rate Refer to the Change Gear Chart on Page 29, orLoosen the apron lock bolt and use the feed lever Figure Threading SetupTo setup for threading, do these steps Change Gear Chart Milling Operations Installing ToolsTo install a tool in the spindle, do these steps Removing ToolsTo position the spindle head vertically, do these steps Headstock PositioningQuill Travel To use the quill, do these stepsTo begin the start up procedure, do these steps Table TravelHigh speed steel cutting chart General Cleaning MaintenanceGeneral Maintenance General LubricationAdjusting/Replacing the V-Belt To replace or adjust the V-belts, do these stepsCross Slide Backlash ServiceCross Slide, Half-Nut Compound Slide Gib Adjustments Electrical Component and Connection Index M1109 Electrical panelElectrical Connections ContactorTransformer connection Wiring Diagram Lathe controlsTroubleshooting Motor & ElectricalOperation and Work Results Parts Diagram Series Parts List PART# DescriptionThread Dial Diagram 1007 1028SPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA