Draytek SM200L General Safety Rules, Important Safety Instructions, USE of this Tool can Generate

Page 4

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in

electric shock, fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

1.FOR YOUR OWN SAFETY, READ THE INSTRUCTION MANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations, and specific hazards will greatly minimize the possibility of accidents and injury.

2.WEAR EYE AND HEARING PROTECTION. ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT. Eye protection equipment should comply with ANSI Z87.1 standards. Hearing equipment should comply with ANSI S3.19 standards.

3.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

4.DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placing arms, hands, and fingers in danger.

5.MAINTAIN ALL TOOLS AND MACHINES IN PEAK CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and machines can further damage the tool or machine and/or cause injury.

6.CHECK FOR DAMAGED PARTS. Before using the machine, check for any damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, and any other conditions that may affect its operation. A guard or any other part that is damaged should be properly repaired or replaced. Damaged parts can cause further damage to the machine and/or injury.

7.KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.

8.KEEP CHILDREN AND VISITORS AWAY. Your shop is a potentially dangerous environment. Children and visitors can be injured.

9.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.

10.USE THE GUARDS. Check to see that all guards are in place, secured, and working correctly to reduce the risk of injury.

11.REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING THE MACHINE. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.

12.USE THE RIGHT MACHINE. Don’t force a machine or an attachment to do a job for which it was not designed. Damage to the machine and/or injury may result.

13.USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by Delta may cause damage to the machine or injury to the

user.

14.USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. See the Extension Cord Chart for the correct size depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

15.SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury.

16.FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, ORABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed.

17.DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result.

18.DON’T OVERREACH. Loss of balance can make you fall into a working machine, causing injury.

19.NEVER STAND ON THE MACHINE. Injury could occur if the tool tips, or if you accidentally contact the cutting tool.

20.NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN THE POWER OFF. Don’t leave the machine until it comes to a complete stop. Achild or visitor could be injured.

21.TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE POWER SOURCE before installing or removing accessories, before adjusting or changing set-ups, or when making repairs. An accidental start-up can cause injury.

22.MAKE YOUR WORKSHOP CHILDPROOF WITH PADLOCKS, MASTER SWITCHES, OR BY REMOVING STARTER KEYS. The accidental start-up of a machine by a child or visitor could cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE. DO NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power tools may result in injury.

24. USE OF THIS TOOL CAN GENERATE

AND DISBURSE DUST OR OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST AND ASBESTOS DUST. Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.

4

Image 4
Contents Motorized Bench Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules Important Safety InstructionsStay ALERT, Watch What YOU are DOING, USE of this Tool can GenerateAdditional Specific Safety Rules Power Connections Grounding InstructionsCarton Contents Functional DescriptionStand for Model TS200LS only FigAssembly Unpacking and CleaningAssembly Tools Required Elevating and Supporting Surfaces for a SAW with no StandAssembling Stand SAW to StandAttaching Blade Height Adjusting Handwheel Attaching Blade Guard and Splitter AssemblyOn the screw L Fig Miter Gauge Attaching Miter Gauge HolderAssembling RIP Fence Illustrates the miter gauge D inserted into the holderLocking Switch in the OFF Position Blade Height AdjustmentOperation Starting and Stopping SAW45 Degree Positive Stop Adjustments Blade Tilt AdjustmentTo Adjust Positive Stop AT 45 Degrees RIP Fence Operation Adjustments Table Insert AdjustmentMiter Gauge Operation Adjustments Adjusting Blade Parallel to Miter Gauge SlotsChanging the Blade CROSS-CUTTINGNever USE the Fence AS a CUT-OFF Gage When CROSS-CUTTING RippingUsing Auxiliary Wood Facing on RIP Fence Accessory Dado CutterheadConstructing a Push Stick Guard Removed for CLARITY. Always USE the GuardPage Pushstick Constructing a Push StickPower Tool Institute Constructing a FeatherboardTroubleshooting WHAT’S WRONG? What to DO…Maintenance ServiceAccessories WarrantySierra Motorizada de Banco de 10 pulg Pautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesProposición DE California Normas Generales DE Seguridad Instrucciones Importantes Sobre SeguridadReglas DE Seguridad Adicionales Para Sierra DE Mesa Guarde Estas InstruccionesConexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraInstrucciones DE Funcionamiento Contenido DE CartonCordones DE Extensión Sierra Motorizada DE Banco PartesSoporte Para EL Modelo TS200LS Fig Desempaquetado Y Limpieza EnsamblajeHerramientas DE Ensamblaje Requeridas Sierra QUE Ensambla Montaje DE LA Base DE Soporte SM200LEnsamblado DEL Volante DE Inclinacion Y Elevado DE Hoja Ensamblado DEL Ensamblaje DE Protector DE Hoya Y Hendidor Aviso No apriete los tornillos C del todo en este momentoEscuadra DE Ingletes Ensamblado DEL Portador DE LA Escuadra DE Ingletes Desconcte LA Maquina DE LA Fuente DE AlimentacionEnsamblado DE LA Guia DE Corte a LO Largo OperaciónArrancando Y Deteniendo LA Sierra Fijando EL Interruptor EN LA Posicion DE Apagado Proteccion Contra SobrecargasControl DE Elevacion Y Bajado DE LA Hoja Control DE Inclinacion DE LA HojaAjustando LOS Topes Positivos DE 90 Y 45 Grados Funcionamiento Y Ajustes DE LA Guia DE Corte a LO LargoAjuste DEL Separador DE Millares DEL Vector Funcionamiento Y Ajustes DE LA Escuadra DE IngletesUtilizar LA Maquina Cambio DE LA HojaRealización DE Cortes Transversales Realización DE Cortes AL HiloConstrucción DE UN Palo DE Empujar El protectorFresa DE Ranurar Accesoria Construcción DE UNA Tabla DE Canto Biselado Guia Localizacion DE Fallas Quel EST LE Problème ? QUE FAIRE…Vara DE Empuje Construcción DE UN Palo DE EmpujarMantenimiento ServicioAccesorios GarantiaScie détabli motorisée de 10 po 25,4 cm Directives DE Sécurité Importantes Conserver CES DirectivesLignes Directrices EN Matière DE Sécurité Définitions Proposition 65 DE LA CalifornieRègles Générales DE Sécurité Directives DE Sécurité ImportantesRègles DE Sécurité Spécifiques Supplémentaires Pour Éviter L’EFFET DE Rebond13. Éviter LES Opérations Maladroites Soutenir Correctement LES Pièces Longues OU LargesConnexions Électriques Directives DE Mise À LA TerreDescription Fonctionnelle Contenu DU CartonRallonges Électriques AVANT-PROPOSPièces Assemblage Désemballage ET NettoyageOutils Nécessaires Pour L’ASSEMBLAGE Surfaces DE Levage ET DE Support Pour UNE Scie Sans SocleAssemblage DU Socle Assemblage DE LA Scie SUR SocleFixation DU Volant Servant À Régler LA Hauteur DE LA Lame Fixation DE Lensemble PARE-MAIN /COUTEAU SéparateurPage Jauge À Onglet Fixation DU PORTE-JAUGE À OngletAssemblage DU Guide Longitudinal Fonctionnement Démarrage ET Arrêt DE LA ScieVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Protection Contre LES SurchargesRéglages DES Butées Fixes À 90 ET 45 Degrés Réglage DE L’INCLINAISON DE LA LameRéglage Dune Butée Fixe À 45 Degrés Utilisation ET Réglages DU Guide Longitudinal Réglage DE Linsert DE TableUtilisation ET Réglages DE LA Jauge À Onglet Changement DE LA Lame TronçonnageSciage EN Long DUN Poussoir » Fraise Accessoire À RainurerEN Bois Auxiliaire Face AU Guide Page « Fabrication DUN Poussoir » Power Tool Institute Sumner Avenue Construction Dune Planche EN ÉventailDépannage Accessoires EntretienRéparation GarantiePORTER-CABLE · Delta Service Centers