Draytek SM200L instruction manual Power Connections, Grounding Instructions

Page 6

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

SHOCK HAZARD. DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

GROUNDING INSTRUCTIONS

SHOCK HAZARD. THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

Your machine is wired for 120 Volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

SHOCK HAZARD. IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. A

6

Fig. B

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Motorized Bench Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionStay ALERT, Watch What YOU are DOING, General Safety RulesImportant Safety Instructions USE of this Tool can GenerateAdditional Specific Safety Rules Power Connections Grounding InstructionsCarton Contents Functional DescriptionStand for Model TS200LS only FigAssembly Tools Required AssemblyUnpacking and Cleaning Elevating and Supporting Surfaces for a SAW with no StandAssembling Stand SAW to StandAttaching Blade Height Adjusting Handwheel Attaching Blade Guard and Splitter AssemblyOn the screw L Fig Miter Gauge Attaching Miter Gauge HolderAssembling RIP Fence Illustrates the miter gauge D inserted into the holderOperation Locking Switch in the OFF PositionBlade Height Adjustment Starting and Stopping SAWBlade Tilt Adjustment 45 Degree Positive Stop AdjustmentsTo Adjust Positive Stop AT 45 Degrees RIP Fence Operation Adjustments Table Insert AdjustmentMiter Gauge Operation Adjustments Adjusting Blade Parallel to Miter Gauge SlotsChanging the Blade CROSS-CUTTINGNever USE the Fence AS a CUT-OFF Gage When CROSS-CUTTING RippingConstructing a Push Stick Using Auxiliary Wood Facing on RIP FenceAccessory Dado Cutterhead Guard Removed for CLARITY. Always USE the GuardPage Pushstick Constructing a Push StickPower Tool Institute Constructing a FeatherboardTroubleshooting WHAT’S WRONG? What to DO…Accessories MaintenanceService WarrantySierra Motorizada de Banco de 10 pulg Instrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESProposición DE California Normas Generales DE Seguridad Instrucciones Importantes Sobre SeguridadReglas DE Seguridad Adicionales Para Sierra DE Mesa Guarde Estas InstruccionesConexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraCordones DE Extensión Instrucciones DE FuncionamientoContenido DE Carton Sierra Motorizada DE Banco PartesSoporte Para EL Modelo TS200LS Fig Ensamblaje Desempaquetado Y LimpiezaHerramientas DE Ensamblaje Requeridas Montaje DE LA Base DE Soporte SM200L Sierra QUE EnsamblaEnsamblado DEL Volante DE Inclinacion Y Elevado DE Hoja Ensamblado DEL Ensamblaje DE Protector DE Hoya Y Hendidor Aviso No apriete los tornillos C del todo en este momentoEscuadra DE Ingletes Ensamblado DEL Portador DE LA Escuadra DE Ingletes Desconcte LA Maquina DE LA Fuente DE AlimentacionOperación Ensamblado DE LA Guia DE Corte a LO LargoArrancando Y Deteniendo LA Sierra Control DE Elevacion Y Bajado DE LA Hoja Fijando EL Interruptor EN LA Posicion DE ApagadoProteccion Contra Sobrecargas Control DE Inclinacion DE LA HojaAjustando LOS Topes Positivos DE 90 Y 45 Grados Funcionamiento Y Ajustes DE LA Guia DE Corte a LO LargoAjuste DEL Separador DE Millares DEL Vector Funcionamiento Y Ajustes DE LA Escuadra DE IngletesUtilizar LA Maquina Cambio DE LA HojaRealización DE Cortes Transversales Realización DE Cortes AL HiloConstrucción DE UN Palo DE Empujar El protectorFresa DE Ranurar Accesoria Construcción DE UNA Tabla DE Canto Biselado Guia Localizacion DE Fallas Quel EST LE Problème ? QUE FAIRE…Vara DE Empuje Construcción DE UN Palo DE EmpujarAccesorios MantenimientoServicio GarantiaScie détabli motorisée de 10 po 25,4 cm Directives DE Sécurité Importantes Conserver CES DirectivesLignes Directrices EN Matière DE Sécurité Définitions Proposition 65 DE LA CalifornieRègles Générales DE Sécurité Directives DE Sécurité Importantes13. Éviter LES Opérations Maladroites Règles DE Sécurité Spécifiques SupplémentairesPour Éviter L’EFFET DE Rebond Soutenir Correctement LES Pièces Longues OU LargesConnexions Électriques Directives DE Mise À LA TerreRallonges Électriques Description FonctionnelleContenu DU Carton AVANT-PROPOSPièces Outils Nécessaires Pour L’ASSEMBLAGE AssemblageDésemballage ET Nettoyage Surfaces DE Levage ET DE Support Pour UNE Scie Sans SocleAssemblage DU Socle Assemblage DE LA Scie SUR SocleFixation DU Volant Servant À Régler LA Hauteur DE LA Lame Fixation DE Lensemble PARE-MAIN /COUTEAU SéparateurPage Jauge À Onglet Fixation DU PORTE-JAUGE À OngletAssemblage DU Guide Longitudinal Verrouiller L’INTERRUPTEUR EN Position D’ARRÊT FonctionnementDémarrage ET Arrêt DE LA Scie Protection Contre LES SurchargesRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésRéglage Dune Butée Fixe À 45 Degrés Utilisation ET Réglages DU Guide Longitudinal Réglage DE Linsert DE TableUtilisation ET Réglages DE LA Jauge À Onglet Changement DE LA Lame TronçonnageSciage EN Long Fraise Accessoire À Rainurer DUN Poussoir »EN Bois Auxiliaire Face AU Guide Page « Fabrication DUN Poussoir » Power Tool Institute Sumner Avenue Construction Dune Planche EN ÉventailDépannage Réparation AccessoiresEntretien GarantiePORTER-CABLE · Delta Service Centers
Top Page Image Contents