Conair CTS 9, CTS 7, CTS 5 manual Length Softkey, Enter or Delete?

Page 63

Conair Servo Traveling Saw

Operator Control Instructions

Length Softkey

By pressing the soft key located under the word Length on the Main Screen, the preset for the Length counter is available.

LENGTH 0000 . 00 0 in .

Exit

The number shown is the current length preset value, i.e. the length to cut the product. A cursor will appear in the least significant digit. The user has a choice of ways to adjust this number.

Exit or Prev- if no change is required press Exit or Prev to return to the Main screen.

Raise will increase the preset by 0.01”. The key can be pressed once for each 0.01” increment required or held down to scroll up. Releasing the key will freeze the preset at the last value.

Lower will decrease the preset by 0.01”. The key can be pressed once for each 0.01” decrement required or held down to scroll down. Releasing the key will freeze the preset at the last value.

Numeric keys

Key in the length required and press enter. The decimal place is fixed so remember this when entering the preset. If you require 24 inches you must key in 24000 and then press enter. Keying only 24 will set the length to 0.024 inches.

Enter or Delete?

If the keyed in number is correct press the enter key for it to be accepted and return to the Main screen. If it is wrong press the delete key and the previous preset will reappear.

Appendix B-1 (7)

Image 63
Contents Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Purpose User Guide HOW the User Guide is OrganizedYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What isHOW the CTS SAW Works SAW Works CTS SAW FeaturesSpecifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the BoxesYou need these tools for installation Preparing for InstallationPositioning the CTS SAW Move the saw into position. Place the saw in posiDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW BladesTesting the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height AdjustmentControl Panels Upper Clamp AdjustmentPower Supply To remove and/or adjust each clamp assemblyPneumatic Cylinder Operation Electrical Operation System Inspection Machine LubricationWait at least five minutes for the blade to stop completely Blade ReplacementChip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Inspecting the blade mounting hardware Maintenance OverviewPreventative Maintenance Schedule Checking saw bladesWeekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosureTroubleshooting FEW Words of Caution Before BeginningIdentifying Cause of a Problem Symptom Possible cause Solution Electrical ProblemsExtrudate Product Quality ProblemsIncorrect blade design Incorrect coolingSolenoid problem Problem Puller problemCounter problem Rodless cylinder problemChecking Servo Amplifier Check the encoder itself. There should be no play Checking the EncoderCheck all connections Check the encoder cable for damage. If necesFrom outside the United States, call WE’RE Here to HelpAppendix A-2 Soft Keys Conair Servo Traveling SawNumeric keys Fixed Function Keys at BottomLCD Screen Contents Starting Comms Power Up SequenceMain Screen Length CounterOn/Off Softkey Exit Softkey Reset SoftkeyTotal Softkey Total ScreenEnter or Delete? Length SoftkeyHome Seek HomingHome Already Maint. Softkey Menu AreaMaint. Area R c t n S o f t k e yChange Softkey Time Softkey S o f t k e yB l e S o f t k e y Cycles SoftkeyAcceptable range is 120.00-1800.00 ipm T u r n S o f t k e y20% V a n c e S o f t k e yMenu Area Factory Softkey Error MessageTable Assembly, Pneumatic / Servo GeneralBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800Volt Electrical Control, 3hp 230/460v