Conair CTS 7, CTS 9, CTS 5 manual WE’RE Here to Help, From outside the United States, call

Page 55

Conair has made the largest investment in customer support in the plastics industry. Our service experts are available to help with any problem you might have installing and operating your equipment. Your Conair sales representative also can help analyze the nature of your problem, assuring that it did not result from misapplication or improper use.

To contact Customer Service personnel, call:

From outside the United States, call: 814-437-6861

You can commission Conair service personnel to provide on- site service by contacting the Customer Service Department. Standard rates include an on-site hourly rate, with a one-day minimum plus expenses.

WE’RE HERE TO HELP

HOW TO CONTACT

CUSTOMER

SERVICE

If you do have a problem, please complete the following checklist before calling Conair:

❒Make sure you have all model, serial and parts list numbers for your particular equipment. Service personnel will need this information to assist you.

❒Make sure power is supplied to the equipment.

❒Make sure that all connectors and wires within and between the saw and related components have been installed correctly.

❒Check the troubleshooting guide of this manual for a solution.

❒Thoroughly examine the instruction manual(s) for associated equipment, especially controls. Each manual may have its own troubleshooting guide to help you.

❒Check that the equipment has been operated as described in this manual.

❒Check accompanying schematic drawings for information on special considerations.

BEFORE YOU

CALL ...

Additional manuals and prints for your Conair equipment may be ordered through the Customer Service or Parts Departments for a nominal fee.

SERVICE INFORMATION

APPENDIX A-1

Image 55

Contents Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction HOW the User Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What isHOW the CTS SAW Works SAW Works CTS SAW FeaturesSpecifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the BoxesYou need these tools for installation Preparing for InstallationMove the saw into position. Place the saw in posi Positioning the CTS SAWDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW BladesTesting the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height AdjustmentControl Panels Upper Clamp AdjustmentPower Supply To remove and/or adjust each clamp assemblyPneumatic Cylinder Operation Electrical Operation System Inspection Machine LubricationWait at least five minutes for the blade to stop completely Blade ReplacementChip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Inspecting the blade mounting hardware Maintenance OverviewPreventative Maintenance Schedule Checking saw bladesWeekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosureTroubleshooting FEW Words of Caution Before BeginningIdentifying Cause of a Problem Symptom Possible cause Solution Electrical ProblemsExtrudate Product Quality ProblemsIncorrect blade design Incorrect coolingSolenoid problem Problem Puller problemCounter problem Rodless cylinder problemChecking Servo Amplifier Check the encoder itself. There should be no play Checking the EncoderCheck all connections Check the encoder cable for damage. If necesFrom outside the United States, call WE’RE Here to HelpAppendix A-2 Soft Keys Conair Servo Traveling SawFixed Function Keys at Bottom Numeric keysLCD Screen Contents Starting Comms Power Up SequenceLength Counter Main ScreenOn/Off Softkey Exit Softkey Reset SoftkeyTotal Softkey Total ScreenEnter or Delete? Length SoftkeyHome Seek HomingHome Already Maint. Softkey Menu AreaR c t n S o f t k e y Maint. AreaChange Softkey Time Softkey S o f t k e yB l e S o f t k e y Cycles SoftkeyAcceptable range is 120.00-1800.00 ipm T u r n S o f t k e y20% V a n c e S o f t k e yMenu Area Factory Softkey Error MessageGeneral Table Assembly, Pneumatic / ServoBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800Volt Electrical Control, 3hp 230/460v