Conair CTS 9, CTS 7, CTS 5 manual Electrical Control, 3hp 230/460v, Volt

Page 75

EQUIPMENT PARTS LIST

TO ORDER PARTS CALL TOLL FREE (800) 458-1960

Product: CTS-5

REV #: 023525L020/0703

Instruction Manual:

Reference	Part
Number	Number	Qty	Description	3 of 3

ÿElectrical Control, 3hp 230/460v (7140360201)

40	27500675	1	Switch Assy. Disconnect
41	27501514	1	Contact, Aux. 1N.O. 1N.C.
42	20973414	1	Breaker, Circuit
43	27500202	1	Contactor, Non Rev. 12 Amp
44	27500923	1	Contacts, Aux. 2N.O. 2N.C.
45	27500109	1	Transformer, 250VA 240/480v
46	20801476	1	Receptacle, Amphenol, 4 Pin
47	20801459	1	Connector, Amphenol, 10 Pin
48	26671601	2	Relay
49	26671602	2	Relay
50	1605-30000	1	Relay, Time
51	1608-30000	7	Semi-Cond. Varistor
52	26666702	1	Connector, Cable Gland

ÿ230 Volt

53	27501510	1	Starter, 6.3-10.0 Amp
54	20604012	2	Fuse, 1.5 Amp Type FNQ
55	1646-30192	1	Receptacle, Flanged

* Indicates recommended spare parts > Indicates revisions change Italicized indicates typographical

Image 75

Contents Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Purpose User Guide HOW the User Guide is OrganizedYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What isHOW the CTS SAW Works SAW Works CTS SAW FeaturesSpecifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the BoxesYou need these tools for installation Preparing for InstallationPositioning the CTS SAW Move the saw into position. Place the saw in posiDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW BladesTesting the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height AdjustmentControl Panels Upper Clamp AdjustmentPower Supply To remove and/or adjust each clamp assemblyPneumatic Cylinder Operation Electrical Operation System Inspection Machine LubricationWait at least five minutes for the blade to stop completely Blade ReplacementChip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Inspecting the blade mounting hardware Maintenance OverviewPreventative Maintenance Schedule Checking saw bladesWeekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosureTroubleshooting FEW Words of Caution Before BeginningIdentifying Cause of a Problem Symptom Possible cause Solution Electrical ProblemsExtrudate Product Quality ProblemsIncorrect blade design Incorrect coolingSolenoid problem Problem Puller problemCounter problem Rodless cylinder problemChecking Servo Amplifier Check the encoder itself. There should be no play Checking the EncoderCheck all connections Check the encoder cable for damage. If necesFrom outside the United States, call WE’RE Here to HelpAppendix A-2 Soft Keys Conair Servo Traveling SawNumeric keys Fixed Function Keys at BottomLCD Screen Contents Starting Comms Power Up SequenceMain Screen Length CounterOn/Off Softkey Exit Softkey Reset SoftkeyTotal Softkey Total ScreenEnter or Delete? Length SoftkeyHome Seek HomingHome Already Maint. Softkey Menu AreaMaint. Area R c t n S o f t k e yChange Softkey Time Softkey S o f t k e yB l e S o f t k e y Cycles SoftkeyAcceptable range is 120.00-1800.00 ipm T u r n S o f t k e y20% V a n c e S o f t k e yMenu Area Factory Softkey Error MessageTable Assembly, Pneumatic / Servo GeneralBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800Volt Electrical Control, 3hp 230/460v