Conair CTS 9, CTS 7, CTS 5 manual Preparing for Installation, You need these tools for installation

Page 21

1 You need these tools for installation:

❒wire strain relief

❒16- or 18-inch adjustable wrench

❒set of Allen wrenches

❒½ inch open or box end wrench

❒flashlight

2 Plan the location. Make sure the area where the saw is installed has the following:

●A grounded power source. Check the saw’s serial- al tag for the correct amps, voltage, phase and cycles. All wiring should be completed by qualified personnel and should comply with your region’s electrical codes.

●Clearance for safe operation and maintenance. Make sure there is enough clearance around the saw for maintenance and servicing.

PREPARING FOR INSTALLATION

WARNING: Improper installation, oper- ation, or servicing may result in equipment damage or personal injury.

This equipment should only be installed, adjust- ed, and serviced by qualified technical person- nel who are familiar with the construction, oper- ation, and potential hazards of this type of machine.

All wiring, disconnects, and fuses should be installed by qualified electrical technicians in accordance with electrical codes in your region. Always maintain a safe ground. Do not operate the equipment at power levels other than what is specified on the machine serial tag and data plate.

UGE058/0803

CTS Saw

INSTALLATION 3-3

Image 21

Contents Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Purpose User Guide HOW the User Guide is OrganizedYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What isHOW the CTS SAW Works SAW Works CTS SAW FeaturesSpecifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the BoxesYou need these tools for installation Preparing for InstallationPositioning the CTS SAW Move the saw into position. Place the saw in posiDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW BladesTesting the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height AdjustmentPower Supply Upper Clamp AdjustmentTo remove and/or adjust each clamp assembly Control PanelsPneumatic Cylinder Operation Electrical Operation System Inspection Machine LubricationWait at least five minutes for the blade to stop completely Blade ReplacementChip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Preventative Maintenance Schedule Maintenance OverviewChecking saw blades Inspecting the blade mounting hardwareWeekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosureTroubleshooting FEW Words of Caution Before BeginningIdentifying Cause of a Problem Symptom Possible cause Solution Electrical ProblemsIncorrect blade design Product Quality ProblemsIncorrect cooling ExtrudateCounter problem Problem Puller problemRodless cylinder problem Solenoid problemChecking Servo Amplifier Check all connections Checking the EncoderCheck the encoder cable for damage. If neces Check the encoder itself. There should be no playFrom outside the United States, call WE’RE Here to HelpAppendix A-2 Soft Keys Conair Servo Traveling SawNumeric keys Fixed Function Keys at BottomLCD Screen Contents Starting Comms Power Up SequenceMain Screen Length CounterOn/Off Softkey Total Softkey Reset SoftkeyTotal Screen Exit SoftkeyEnter or Delete? Length SoftkeyHome Seek HomingHome Already Maint. Softkey Menu AreaMaint. Area R c t n S o f t k e yChange Softkey Time Softkey S o f t k e yB l e S o f t k e y Cycles SoftkeyAcceptable range is 120.00-1800.00 ipm T u r n S o f t k e y20% V a n c e S o f t k e yMenu Area Factory Softkey Error MessageTable Assembly, Pneumatic / Servo GeneralBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800Volt Electrical Control, 3hp 230/460v