Conair CTS 5, CTS 9, CTS 7 manual Machine Frame Support System, Blade Height Adjustment

Page 32

MACHINE

FRAME AND

SUPPORT

SYSTEM

The machine frame is constructed of welded steel that has been primed and painted to resist corrosion and provide a maintenance free finish. The frame is supported by, four level- ing screws, that both permanently fix the position of the unit and also help accommodate any uneven flooring. These screws have a welded hex nut to allow adjustment with a wrench.

The motors and machine components are mounted inside the frame and completely guarded for operator safety.

These and all guards should always remain securely in place when machine is running and should be re-installed after any maintenance procedures that have required their removal.

BLADE HEIGHT ADJUSTMENT

The saw blades are mounted to and driven by a 3500 RPM arbor motor. This motor is mounted on a pivot assembly, which guides and secures the saw blade through the cutting process.

There is adjustment for how high the saw blade will extend through the table depending on the product being cut. For maximum cut cycles, the saw blade should be adjusted so that the blade just passes through the product before returning home. Too much blade extension will waste valuable time and limit the amount of cuts that will be available per minute. This adjustment is made externally with the hand knob positioned at the rear of the cutting table. Turning the knob counterclock- wise will allow the blade to extend farther up through the table and turning the knob clockwise will reduce the amount that the blade will come up.

4-4OPERATION

CTS Saw

UGE058/0803

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Your Responsibility AS a User Purpose User GuideHOW the User Guide is Organized Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt HOW to USE Lockout Device Turn the rotary disconnect switch to OFF or O positionPage Description What is Typical ApplicationsHOW the CTS SAW Works SAW Works Features CTS SAWSpecifications Optional Equipment Left to right machine operationPage Installation Unpacking the Boxes Carefully uncrate the saw and its componentsPreparing for Installation You need these tools for installationDetermine the best distance from the belt puller to Positioning the CTS SAWMove the saw into position. Place the saw in posi Position the SAW Connecting Main Power Source Installing the Encoder Installing the SAW Blades Remove the hex nutPreparing for Testing Testing the InstallationPage Operation SAW Control Control Features Blade Height Adjustment Machine Frame Support SystemUpper Clamp Adjustment Power SupplyTo remove and/or adjust each clamp assembly Control PanelsPneumatic Cylinder Operation Electrical Operation Machine Lubrication System InspectionBlade Replacement Wait at least five minutes for the blade to stop completelyChip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Maintenance Overview Preventative Maintenance ScheduleChecking saw blades Inspecting the blade mounting hardwareWeekly Checking Blades Checking Electrical Connections Open the electrical enclosure Close the electrical enclosure doorTroubleshooting Before Beginning FEW Words of CautionIdentifying Cause of a Problem Electrical Problems Symptom Possible cause SolutionProduct Quality Problems Incorrect blade designIncorrect cooling ExtrudateProblem Puller problem Counter problemRodless cylinder problem Solenoid problemChecking Servo Amplifier Checking the Encoder Check all connectionsCheck the encoder cable for damage. If neces Check the encoder itself. There should be no playWE’RE Here to Help From outside the United States, callAppendix A-2 Conair Servo Traveling Saw Soft KeysLCD Screen Numeric keysFixed Function Keys at Bottom Contents Power Up Sequence Starting CommsOn/Off Softkey Main ScreenLength Counter Reset Softkey Total SoftkeyTotal Screen Exit SoftkeyLength Softkey Enter or Delete?Homing Home SeekHome Already Menu Area Maint. SoftkeyChange Softkey Maint. AreaR c t n S o f t k e y S o f t k e y Time SoftkeyCycles Softkey B l e S o f t k e yT u r n S o f t k e y Acceptable range is 120.00-1800.00 ipmV a n c e S o f t k e y 20%Error Message Menu Area Factory SoftkeyBlades Opt Table Assembly, Pneumatic / ServoGeneral Equipment Parts List To Order Parts Call Toll Free 800 Servo Opt. / Table TravelElectrical Control, 3hp 230/460v Volt
Top Page Image Contents