Bosch Power Tools GTS1031 manual DAdO CUTTINg, INSTAllINg a dAdO SET, USINg STACKEd dAdO Sets

Page 32
! WARNING
! WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 32

dAdO CUTTINg

Instructions for operating the saw with Dado Head sets are contained in the booklet furnished with these accessories.

ALWAYS USE AN APPROPRIATE BOSCH TABLE INSERT AND WASHERS LISTED UNDER REC- OMMENDED ACCESSORIES (see page 35).

ALWAYS PLACE THE BLADE WASHERS IN THE ORIGINAL POSITIONS WHEN YOU ARE FIN- ISHED DADO CUTTING.

INSTAllINg A dAdO SET

A dado set is an accessory system used to make non-thru grooves or lap cuts on work pieces. These tools are commonly used in furniture and cabinet building. After work pieces have been properly dado cut, they can be tightly joined together. The GTS1031 table saw can accommodate dado cutting up to 1/2” wide in a single pass.

To reduce the risk of injury, al- ways disconnect plug from

power source before changing blades.

To reduce the risk of injury, al- ways use the bosch dado blade Table Insert No.TS1013 (comes with a dado ac-

cessory washer). Never make dado cuts without this insert. Do not use dado sets larger than 8” di- ameter. Never set dado cutters to any bevel angle other than the vertical 0° angle. Follow all warnings and instructions shown here and those that accom- pany your dado set. Failure to comply with these warnings may result in serious bodily injuries.

! WARNING

To reduce the risk of injury, do

 

not use dado sets larger than 8

 

inches in diameter. The saw is not designed to ac- cept larger sized dados.

USINg STACKEd dAdO SETS

NOTE: These instructions are based on using the

Bosch 8” and 6” Professional Dado Sets: Model Nos. PRO824DADO, PRO840DADO and PRO624DADO. They also apply to most standard stacked dado sets.

1.Disconnect plug from power source.

2.Remove the Barrier Guard Assembly and Anti- Kickback Device (see pages 12 & 13). Lower and lock the Riving Knife in its lowest position.

3.Remove standard table insert plate. Raise saw blade to maximum height.

4.Remove the arbor nut, then outer washer, and saw blade, (see page 15). Note: For only dado cutting, leave the inner washer in place. The outer washer will be replaced with the combination nut/washer included with the TS1013 insert.

5.Installing a dado stack (Fig. 55)

A)Place the desired parts of the dado set onto the arbor shaft.

B)Place the desired parts of the dado set onto the arbor shaft.

C)Place the supplied combination nut/washer from the Dado Accessory Kit (TS1013) onto the outside of the dado stack and tighten.

6. Placing dado blades and chippers: (see Fig. 55)

For 1/4” wide cuts, place the two outside dado blades (cutters) on the shaft. The two dado out- side blades may be different, check for informa- tion on the blade and the manufacturer's instructions for proper installation.

For wider cuts (up to 1/2” maximum), chipper blades and spacers can be placed only between the outside blades (cutters).

FIG. 55

INNER BLADE

 

 

WASHER

COMBINATION

 

 

 

 

NUT/WASHER

 

ARBOR

 

INNER BLADE

OUTER BLADE

CHIPPERS

-32-

Image 32
Contents BM 2610014415 01-11 EBM 2610012089 12-10 E 1/10/11 717 AM Ver la páginaGeneral Safety Rules Secure WorkAdditional Safety Rules PROTECTION To AVOId bEINg pUllEdInto the SpINNINg TOOl DO not Wear loose fitting glovesThink SAfETy That AppEAR on the fRONT Of yOUR TAblE SAWTable of Contents Double Insulated ToolsGlossary of Terms CrosscutTools Needed for Assembly And Adjustment THICK. this EdgeMust be Perfectly Phillips Screwdriver StraightGetting To Know your Table Saw 10 9Miter gAUgE CORd WRApRIp fENCE STORAgE PUSH Stick & WRENCH STORAgEUnpacking And Checking Contents Assembly ATTACHINg the gUARd ASSEMblyATTACHINg the Smart gUARd SySTEM POSITIONINg the RIVINg KNIfEATTACHINg the ANTI-KICKbACK dEVICE REMOVAl ANd INSTAllATION Of the blAdE USINg the Correct blAdEUSINg CARbIdE-TIppEd blAdES CHANgINg the blAdERemove the table insert 1 Fig ATTACHINg RIp fENCE fOR USE STORAgEWasher HEX NUT MOUNTINg the TAblE SAWHEX Bolt Adjustments AdjUSTINg 0 ANd 45 dEgREE POSITIVE STOpSPower source when making adjustments AdjUSTINg 0 dEgREE pOSITIVE STOpAdjUSTINg blAdE pARAllEl to Miter gAUgE SlOTS Blade was adjusted parallel to the miter gaugePower source before making any adjustments Under Rear of TableTo SET the RIp fENCE pOINTER RIp fENCE pOINTER AdjUSTMENTAlIgNINg RIp fENCE TAblE pOINTER AdjUSTMENT Disconnect plug from powerAdjUSTINg RIVINg KNIfE CHECKINg RIVINg KNIfE AlIgNMENTAdjUSTINg the TAblE Insert Should be at the same level. If adjustment is necesGTS1031 table insert slot includes four 4 ad Justment screws 9 to set the height . PlaceBasic Table Saw Operation SySTEM STORAgE USINg the RIp fENCE pOINTER When TAblE is not EXTENdEdUSINg the TAblE pOINTER When TAblE is EXTENdEd BlAdE bEVEl CONTROlNotch Edges Must be ParallelThis Face This Edge Must beUSINg the Miter gAUgE To adjust the miter angleMiter gAUgE AUXIlIARy fACINg ExampleCROSSCUTTINg REpETITIVE CUTTINg Miter CUTTINgBEVEl CROSSCUTTINg COMpOUNd Miter CUTTINgParts Required USINg the RIp fENCERIp fENCE AUXIlIARy fACINg BEVEl RIppINg Push BlockWork Support RAbbETINgFirst CUT Rabbet Second CUT Rabbeting Along Edge Rabbeting Across ENDINSTAllINg a dAdO SET Power source before changing bladesUSINg STACKEd dAdO Sets DAdO CUTTINgDado Table Insert To reduce the risk of injuryRETURNINg SAW to NORMAl THRU-CUTTINg Maintenance Maintaining your Table SawSpECIAl CUTTINg Techniques CUTTINg METAlS ANd MASONRyRecommended Accessories Cat. NoTroubleshooting Consignes générales de sécurité Zone de travailSécurité de l’utilisateur Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilProtection Yeux, mains, visage, oreilles et reste du corps Normes Ansi LA Sécurité Avant ToutAux Rallonges Double isolationTable des matières Lexique Outils nécessaires à l’assemblage et aux réglages Familiarisez-vous avec votre scie de table Table DE Coupe Guide DE Coupe AngulaireRangement DU Cordon Rangement DU Poussoir ET DES Clés HexagonalesOuverture de l’emballage et vérification du contenu Liste DES Pièces FourniesDescription Ensemble table et socle Guide de refenteAssemblage Montage DU Système Smart GuardPositionnement DU Couteau Diviseur Remettez lélément rapporté de la table à sa place FigBM 2610014415 01-11 FBM 2610012089 12-10 F 1/10/11 715 AM Utiliser LA Lame Correcte Retrait ET Installation DE LA LameBM 2610014415 01-11 FBM 2610012089 12-10 F 1/10/11 716 AM Changement DE LA Lame Retirez l’écrou de fixation de l’arbre 4 et la bride 5 FigRangement DU Guide DE Refente Installation DE LA Scie DE TableMontage DU Guide DE Refente Pour Emploi ET Rangement Réglages Réglage DES Butées Fixes À 90 ETRéglage DE LA Butée Fixe À 0 Degré Réglage DE LA Butée Fixe À 45 DegrésAU-DESSOUS DE ’AVANT DE LA Table AU-DESSOUS DE L’ARRIÈRE Suivre ci-dessousPour éviter de subir des Pour Régler Lindicateur DU Guide DE Refente Alignement DU Guide DE RefentePour éviter de subir des Réglage DE L’INDICATEUR DE LA Table Alignement DU Couteau DiviseurBois VUE DE Dessus Réglage DU Couteau DiviseurSoit aligné avec la lame Après avoir réalisé tous les réglagesSerrez lécrou Ment correctUtilisation de la scie de table Interrupteur DE SûretéComposants Figure ❶ Couteau diviseur ❷ Barrière de sécurité principaleRangement DU Système Bord DE LA Réglage DE L’INCLINAISON DE LA LameRéglage DE LA Rallonge DE Table Accessoires DE Sciage Remarque Toutes les dimensions sont en poucesExtrémité EncocheUtilisation DU Guide DE Coupe Angulaire Réglage DU Guide DE Coupe AngulairePièce D’APPOINT Auxiliaire DU Guide DE Coupe Angulaire ExempleCoupe Transversale Coupe Répétitive ’utilisez jamais le guide deCoupe Angulaire Coupe Transversale BiseautéeUtilisation DU Guide DE Refente Pièce Dappoint Auxiliaire Pour LE Guide DE RefentePièces requises Deux 2 brides de fixationCoupe EN Long Biseautée SERRE-JOINTS EN C Support Réalisation DE FeuilluresRetirez le protège-lame Première CoupeDébrancher la fiche de la prise de courant Coupes DE RainuresUtilisation Densembles DE Lames Rainurer Empilées Ensembles DE Lames À Rainurer Réglables OU Oscillantes Plaque Amovible DE Table Pour RainurageEntretien de la scie de table Techniques DE Coupe SpécialiséesCoupe DE Métaux ET DE Maçonnerie EntretienArticle No. de cat Accessoires recommandésLubrification Guide de diagnostic Normas generales de seguridad Area de trabajoSeguridad personal Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaNo USE Guantes que queden holgadosRopa holgada Corbata, joyasPiense EN LA Seguridad UtilizaciónMecánica Puede ObjetosHerramientas con aislamiento doble IndiceHerramientas CON Aislamiento Doble Cordones DE ExtensiónGlosario de términos Herramientas necesarias para el ensamblaje y el ajuste Familiarización con la sierra de mesa Calibre DE Ingletes Enrollador DEL CordonArea Para Guardar EL TOPE-GUIA Para Cortar AL Hilo Mango DE Transporte CON UNA ManoDesempaquetado y comprobación del contenido Para evitar lesiones debidas alSi falta alguna pieza, no intente Tabla DE Piezas Sueltas Articulo DescripcionEnsamblaje Posicionamiento DE LA Cuchilla SeparadoraColoque de nuevo el accesorio de inserción de la mesa Fig Instalación DEL Ensamblaje DEL ProtectorInstalación DEL Dispositivo Antirretroceso Remoción E Instalación DE LA Hoja Utilización DE LA Hoja CorrectaCambio DE LA Hoja Utilización DE Hojas CON Punta DE CarburoTuercas hexagonales de 1/4 Para Utilización Y AlmacenamientoMontaje DE LA Sierra DE Mesa Ajustes Fuente de energía al realizar ajustesAjuste DEL Tope Positivo DE 0 Grados Ajuste DEL Tope Positivo DE 45 GradosLos pasos que se indican a continuación Debajo DE LA Parte Trasera DE LA MesaDeseada en la escala 8 Fig Alineación DEL TOPE-GUÍA Para Cortar AL HiloAjuste DEL Indicador DE LA Mesa Para evitar lesiones corporalesComprobación DE LA Alineación DE LA Cuchilla Separadora Ajuste DE LA Cuchilla SeparadoraLínea con la hoja La hoja. Si es necesario, reajuste la cuchillaDespués de completar los ajustes Alineación correctaFuncionamiento básico de la sierra de mesa Interruptor DE Encendido DE SeguridadPiezas Componentes Figura INSTALACIÓN/DESINSTALACIÓNAlmacenamiento DEL Sistema Como cortar mortajas o rebajosRetroceso y levantando el dispositivo Control DE Inclinación DE LA Hoja Ajuste DE LA Extensión DE LA MesaCuerpo DEL TOPE-GUÍAAyudantes DE Trabajo MuescaPalo DE Empujar Y Bloque DE Empujar ParalelosEjemplo Utilización DEL Calibre DE IngletesPara Ajustar EL Ángulo DE Inglete BM 2610014415 01-11 SBM 2610012089 12-10 S 1/10/11 714 AM Material ni POR Ninguna Otra RazonCortes Repetitivos Corte a IngleteCorte Transversal EN Bisel Corte a Inglete CompuestoDos 2 abrazaderas Refrentado Auxiliar Para EL TOPE-GUÍA Para Cortar AL HiloPiezas necesarias 100 Corte AL Hilo EN Bisel101 Pieza DECorte DE Rebajos Quite el protector de la hoja102 Corte DE MortajasInstalación DE UN Juego DE Mortajar Fuente de energía antes de cambiar las hojas103 Accesorio DE Inserción DE LA Mesa DE MortajarMantenimiento de la sierra de mesa 104Técnicas DE Corte Especiales Corte DE Metales Y Mampostería105 LubricaciónArtículo No. de cat GTS500Localización y reparación de averías 106Remarques Notas 1072610014415

GTS1031 specifications

The Bosch Power Tools GTS1031 is a compact job site table saw designed to deliver precision cutting in a portable format. This powerful saw is equipped with a robust 15-amp motor that can easily handle a wide variety of applications, making it an excellent choice for contractors and DIY enthusiasts alike.

One of the standout features of the GTS1031 is its Smart Guard System. This integrated safety feature includes a modular blade guard, riving knife, and anti-kickback pawls. The blade guard helps protect the user from accidental contact with the blade, while the riving knife reduces the risk of kickback during operation. The entire system is designed to be easy to install and adjust, promoting both safety and efficiency on the job.

The GTS1031 boasts a portable, lightweight design that weighs just 52 pounds. This makes it easy to transport, set up, and store. Its foldable stand provides a stable base while offering simple setup and breakdown without the need for additional tools. The compact size of the saw, along with its sturdy construction, makes it extremely convenient for use in tight spaces or on busy job sites.

Another notable characteristic of the GTS1031 is its cutting capacity. With a 10-inch blade, it can make cuts up to 26 inches wide with a depth of 3.5 inches at 90 degrees and 2.5 inches at 45 degrees. The precision machined aluminum table ensures accurate cuts and durability, while the integrated measurements allow for easy adjustments and repeatability.

The saw features an onboard storage system for its accessories, ensuring that everything needed for operation is within arm's reach. This organization helps users stay efficient, reducing downtime during projects. The table saw is also designed for easy blade changes, minimizing interruption and allowing users to switch between different types of blades based on their cutting needs.

With its blend of power, portability, and safety features, the Bosch Power Tools GTS1031 stands out as a reliable choice for both professionals and hobbyists. Its emphasis on precision and user-friendly design makes it an indispensable tool for a wide range of applications, from framing to fine woodworking.