Bosch Power Tools GTS1031 manual REMOVAl ANd INSTAllATION Of the blAdE, USINg the Correct blAdE

Page 14
! WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 14

REMOVAl ANd INSTAllATION Of THE blAdE

!WARNING Disconnect plug from power source before performing any as-

sembly, adjustment or repair to avoid possible injury.

USINg THE CORRECT blAdE

IMpORTANT: The saw blade provided on this tool has a carbide-tipped kerf width of .102” and a plate (body) thickness that is .071” thick. When looking for a replacement blade, select one with dimensions close to the original blade. This information may not be printed on the blades packaging. If not, check the manufacturers catalog or website. Bosch offers an extensive line of Premium-Quality Professional Saw Blades that match the requirements for this tool. You must select a blade with a kerf width of .092” or more and a plate (body) thickness .088” or less (Fig. 10).

To reduce the risk of injury, do not use extra thin kerf saw blades. The kerf of the blade must be wider than

.092”. Extra thin kerf saw blades (less than .092”) may cause the work piece to bind against the riving knife during cutting. It is recommended that the kerf of the replacement blade used on this saw be .092” or more.

FIG. 10

FIG. 11

! WARNING

To reduce the risk of injury, do

2

not use saw blades made with a

1

thick body plate. If the replacement saw blade's

 

plate thickness is greater than .088”, the riving knife

 

would not properly serve as an aid to reduce kick-

 

back. The replacement blade's plate thickness must

 

be less than .088”.

 

! WARNING

To reduce the risk of injury, do

 

 

not use blade “dampeners,”

 

“stabilizers,” or “stiffening collars” on both

 

sides of a replacement blade. These are metal

 

plates positioned against the sides of the blade to

 

reduce deflection that may occur when using thin

 

saw blades. Use of these devices on both sides will

 

prevent the blade from being properly aligned with

 

the riving knife, which may bind the work piece dur-

 

ing cutting. One “stabilizer” plate may be placed only

3

against the outside of a thin replacement blade.

 

These plates are not required with the supplied

Bosch blade.

-14-

Page 13 Page 15
Image 14
Page 13 Page 15
Contents BM 2610014415 01-11 EBM 2610012089 12-10 E 1/10/11 717 AM Ver la páginaGeneral Safety Rules Secure WorkAdditional Safety Rules Into the SpINNINg TOOl PROTECTIONTo AVOId bEINg pUllEd DO not Wear loose fitting glovesThink SAfETy That AppEAR on the fRONT Of yOUR TAblE SAWTable of Contents Double Insulated ToolsGlossary of Terms CrosscutMust be Perfectly Tools Needed for Assembly And AdjustmentTHICK. this Edge Phillips Screwdriver StraightGetting To Know your Table Saw 10 9RIp fENCE STORAgE Miter gAUgECORd WRAp PUSH Stick & WRENCH STORAgEUnpacking And Checking Contents ATTACHINg the Smart gUARd SySTEM AssemblyATTACHINg the gUARd ASSEMbly POSITIONINg the RIVINg KNIfEATTACHINg the ANTI-KICKbACK dEVICE REMOVAl ANd INSTAllATION Of the blAdE USINg the Correct blAdERemove the table insert 1 Fig USINg CARbIdE-TIppEd blAdESCHANgINg the blAdE ATTACHINg RIp fENCE fOR USE STORAgEWasher HEX NUT MOUNTINg the TAblE SAWHEX Bolt Power source when making adjustments AdjustmentsAdjUSTINg 0 ANd 45 dEgREE POSITIVE STOpS AdjUSTINg 0 dEgREE pOSITIVE STOpPower source before making any adjustments AdjUSTINg blAdE pARAllEl to Miter gAUgE SlOTSBlade was adjusted parallel to the miter gauge Under Rear of TableTo SET the RIp fENCE pOINTER RIp fENCE pOINTER AdjUSTMENTAlIgNINg RIp fENCE AdjUSTINg RIVINg KNIfE TAblE pOINTER AdjUSTMENTDisconnect plug from power CHECKINg RIVINg KNIfE AlIgNMENTGTS1031 table insert slot includes four 4 ad AdjUSTINg the TAblE InsertShould be at the same level. If adjustment is neces Justment screws 9 to set the height . PlaceBasic Table Saw Operation SySTEM STORAgE USINg the TAblE pOINTER When TAblE is EXTENdEd USINg the RIp fENCE pOINTERWhen TAblE is not EXTENdEd BlAdE bEVEl CONTROlThis Face NotchEdges Must be Parallel This Edge Must beMiter gAUgE AUXIlIARy fACINg USINg the Miter gAUgETo adjust the miter angle ExampleCROSSCUTTINg BEVEl CROSSCUTTINg REpETITIVE CUTTINgMiter CUTTINg COMpOUNd Miter CUTTINgParts Required USINg the RIp fENCERIp fENCE AUXIlIARy fACINg BEVEl RIppINg Push BlockFirst CUT Work SupportRAbbETINg Rabbet Second CUT Rabbeting Along Edge Rabbeting Across ENDUSINg STACKEd dAdO Sets INSTAllINg a dAdO SETPower source before changing blades DAdO CUTTINgDado Table Insert To reduce the risk of injuryRETURNINg SAW to NORMAl THRU-CUTTINg SpECIAl CUTTINg Techniques MaintenanceMaintaining your Table Saw CUTTINg METAlS ANd MASONRyRecommended Accessories Cat. NoTroubleshooting Sécurité de l’utilisateur Consignes générales de sécuritéZone de travail Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilProtection Yeux, mains, visage, oreilles et reste du corps Normes Ansi LA Sécurité Avant ToutAux Rallonges Double isolationTable des matières Lexique Outils nécessaires à l’assemblage et aux réglages Familiarisez-vous avec votre scie de table Rangement DU Cordon Table DE CoupeGuide DE Coupe Angulaire Rangement DU Poussoir ET DES Clés HexagonalesDescription Ouverture de l’emballage et vérification du contenuListe DES Pièces Fournies Ensemble table et socle Guide de refentePositionnement DU Couteau Diviseur AssemblageMontage DU Système Smart Guard Remettez lélément rapporté de la table à sa place FigBM 2610014415 01-11 FBM 2610012089 12-10 F 1/10/11 715 AM Utiliser LA Lame Correcte Retrait ET Installation DE LA LameBM 2610014415 01-11 FBM 2610012089 12-10 F 1/10/11 716 AM Changement DE LA Lame Retirez l’écrou de fixation de l’arbre 4 et la bride 5 FigRangement DU Guide DE Refente Installation DE LA Scie DE TableMontage DU Guide DE Refente Pour Emploi ET Rangement Réglage DE LA Butée Fixe À 0 Degré RéglagesRéglage DES Butées Fixes À 90 ET Réglage DE LA Butée Fixe À 45 DegrésAU-DESSOUS DE ’AVANT DE LA Table AU-DESSOUS DE L’ARRIÈRE Suivre ci-dessousPour éviter de subir des Pour Régler Lindicateur DU Guide DE Refente Alignement DU Guide DE RefentePour éviter de subir des Bois VUE DE Dessus Réglage DE L’INDICATEUR DE LA TableAlignement DU Couteau Diviseur Réglage DU Couteau DiviseurSerrez lécrou Soit aligné avec la lameAprès avoir réalisé tous les réglages Ment correctComposants Figure ❶ Couteau diviseur Utilisation de la scie de tableInterrupteur DE Sûreté ❷ Barrière de sécurité principaleRangement DU Système Bord DE LA Réglage DE L’INCLINAISON DE LA LameRéglage DE LA Rallonge DE Table Extrémité Accessoires DE SciageRemarque Toutes les dimensions sont en pouces EncochePièce D’APPOINT Auxiliaire DU Guide DE Coupe Angulaire Utilisation DU Guide DE Coupe AngulaireRéglage DU Guide DE Coupe Angulaire ExempleCoupe Transversale Coupe Angulaire Coupe Répétitive’utilisez jamais le guide de Coupe Transversale BiseautéePièces requises Utilisation DU Guide DE RefentePièce Dappoint Auxiliaire Pour LE Guide DE Refente Deux 2 brides de fixationCoupe EN Long Biseautée Retirez le protège-lame SERRE-JOINTS EN C SupportRéalisation DE Feuillures Première CoupeDébrancher la fiche de la prise de courant Coupes DE RainuresUtilisation Densembles DE Lames Rainurer Empilées Ensembles DE Lames À Rainurer Réglables OU Oscillantes Plaque Amovible DE Table Pour RainurageCoupe DE Métaux ET DE Maçonnerie Entretien de la scie de tableTechniques DE Coupe Spécialisées EntretienArticle No. de cat Accessoires recommandésLubrification Guide de diagnostic Seguridad personal Normas generales de seguridadArea de trabajo Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaRopa holgada No USEGuantes que queden holgados Corbata, joyasMecánica Puede Piense EN LA SeguridadUtilización ObjetosHerramientas CON Aislamiento Doble Herramientas con aislamiento dobleIndice Cordones DE ExtensiónGlosario de términos Herramientas necesarias para el ensamblaje y el ajuste Familiarización con la sierra de mesa Area Para Guardar EL TOPE-GUIA Para Cortar AL Hilo Calibre DE IngletesEnrollador DEL Cordon Mango DE Transporte CON UNA ManoSi falta alguna pieza, no intente Desempaquetado y comprobación del contenidoPara evitar lesiones debidas al Tabla DE Piezas Sueltas Articulo DescripcionColoque de nuevo el accesorio de inserción de la mesa Fig EnsamblajePosicionamiento DE LA Cuchilla Separadora Instalación DEL Ensamblaje DEL ProtectorInstalación DEL Dispositivo Antirretroceso Remoción E Instalación DE LA Hoja Utilización DE LA Hoja CorrectaCambio DE LA Hoja Utilización DE Hojas CON Punta DE CarburoTuercas hexagonales de 1/4 Para Utilización Y AlmacenamientoMontaje DE LA Sierra DE Mesa Ajuste DEL Tope Positivo DE 0 Grados AjustesFuente de energía al realizar ajustes Ajuste DEL Tope Positivo DE 45 GradosLos pasos que se indican a continuación Debajo DE LA Parte Trasera DE LA MesaDeseada en la escala 8 Fig Alineación DEL TOPE-GUÍA Para Cortar AL HiloComprobación DE LA Alineación DE LA Cuchilla Separadora Ajuste DEL Indicador DE LA MesaPara evitar lesiones corporales Ajuste DE LA Cuchilla SeparadoraDespués de completar los ajustes Línea con la hojaLa hoja. Si es necesario, reajuste la cuchilla Alineación correctaPiezas Componentes Figura Funcionamiento básico de la sierra de mesaInterruptor DE Encendido DE Seguridad INSTALACIÓN/DESINSTALACIÓNAlmacenamiento DEL Sistema Como cortar mortajas o rebajosRetroceso y levantando el dispositivo Cuerpo DEL Control DE Inclinación DE LA HojaAjuste DE LA Extensión DE LA Mesa TOPE-GUÍAPalo DE Empujar Y Bloque DE Empujar Ayudantes DE TrabajoMuesca ParalelosEjemplo Utilización DEL Calibre DE IngletesPara Ajustar EL Ángulo DE Inglete BM 2610014415 01-11 SBM 2610012089 12-10 S 1/10/11 714 AM Material ni POR Ninguna Otra RazonCorte Transversal EN Bisel Cortes RepetitivosCorte a Inglete Corte a Inglete CompuestoDos 2 abrazaderas Refrentado Auxiliar Para EL TOPE-GUÍA Para Cortar AL HiloPiezas necesarias 100 Corte AL Hilo EN BiselCorte DE Rebajos 101Pieza DE Quite el protector de la hojaInstalación DE UN Juego DE Mortajar 102Corte DE Mortajas Fuente de energía antes de cambiar las hojas103 Accesorio DE Inserción DE LA Mesa DE MortajarTécnicas DE Corte Especiales Mantenimiento de la sierra de mesa104 Corte DE Metales Y MamposteríaArtículo No. de cat 105Lubricación GTS500Localización y reparación de averías 106Remarques Notas 1072610014415

GTS1031 specifications

The Bosch Power Tools GTS1031 is a compact job site table saw designed to deliver precision cutting in a portable format. This powerful saw is equipped with a robust 15-amp motor that can easily handle a wide variety of applications, making it an excellent choice for contractors and DIY enthusiasts alike.

One of the standout features of the GTS1031 is its Smart Guard System. This integrated safety feature includes a modular blade guard, riving knife, and anti-kickback pawls. The blade guard helps protect the user from accidental contact with the blade, while the riving knife reduces the risk of kickback during operation. The entire system is designed to be easy to install and adjust, promoting both safety and efficiency on the job.

The GTS1031 boasts a portable, lightweight design that weighs just 52 pounds. This makes it easy to transport, set up, and store. Its foldable stand provides a stable base while offering simple setup and breakdown without the need for additional tools. The compact size of the saw, along with its sturdy construction, makes it extremely convenient for use in tight spaces or on busy job sites.

Another notable characteristic of the GTS1031 is its cutting capacity. With a 10-inch blade, it can make cuts up to 26 inches wide with a depth of 3.5 inches at 90 degrees and 2.5 inches at 45 degrees. The precision machined aluminum table ensures accurate cuts and durability, while the integrated measurements allow for easy adjustments and repeatability.

The saw features an onboard storage system for its accessories, ensuring that everything needed for operation is within arm's reach. This organization helps users stay efficient, reducing downtime during projects. The table saw is also designed for easy blade changes, minimizing interruption and allowing users to switch between different types of blades based on their cutting needs.

With its blend of power, portability, and safety features, the Bosch Power Tools GTS1031 stands out as a reliable choice for both professionals and hobbyists. Its emphasis on precision and user-friendly design makes it an indispensable tool for a wide range of applications, from framing to fine woodworking.
Top Page Image Contents