Graco 3A1705J important safety instructions USB Data, USB Logs, Event Log, Job Log

Page 89

USB Data

USB Data

USB Logs

Note

The ADM can read/write to FAT (File Allocation Table) storage devices. NTFS, used by 32 GB or greater storage devices, is not supported.

During operation, the ADM stores system and performance related information to memory in the form of log files. The ADM maintains four log files:

Event Log

Job Log

Daily Log

System Software Log

Blackbox Log

Follow Download Procedure, page 91, to retrieve log files.

Each time a USB flash drive is inserted into the ADM USB port, a new folder named DATAxxxx is created. The number at the end of the folder name increases each time a USB flash drive is inserted and data is downloaded or uploaded.

Event Log

The event log file name is 1–EVENT.CSV and is stored in the DATAxxxx folder.

The event log maintains a record of the last 49,182 events and errors. Each event record contains:

Date of event code

Time of event code

Event code

Event type

Action taken

Event Description

Event codes include both error codes (alarms, deviations, and advisories) and record only events.

Actions Taken includes setting and clearing event conditions by the system, and acknowledging error conditions by the user.

Job Log

The job log file name is 2–JOB.CSV and is stored in the DATAxxxx folder.

The job log maintains a record of data points based on the USB Log Frequency defined in the Setup screens. The ADM stores the last 415,413 data points for download. See Setup - Advanced Screen 3 — USB, page 46, for information on setting the Download Depth and USB Log Frequency.

Data point date

Data point time

A side heat exchanger temperature

A side boost heater temperature

B side heat exchanger temperature

B side boost heater temperature

Hose temperature

Engine coolant temperature

A side temperature setpoint

B side temperature setpoint

Hose temperature setpoint

A side pressure

B side pressure

Pressure setpoint

System lifetime pump cycle counts

Pressure, volume, and temperature units

3A1705J

89

Image 89
Contents Instructions Important Safety InstructionsContents Electric Shock Hazard Skin Injection Hazard Pressurized Aluminum Hazard Battery Hazard Isocyanate Conditions Important Two-Component Material InformationMaterial Self-Ignition Moisture Sensitivity of IsocyanatesChanging Materials Foam Resins with 245 fa Blowing AgentsXP2i Series Proportioner Models30i Series Approvals SystemsSystems with Air Compressor AccessoriesRelated Manuals Supplied ManualsTypical Installation, with circulation Typical Installation, without circulation Proportioner Control Panel, Component IdentificationGG Generator, MM Motor Control Module MCM, High Power Temperature Control ModuleGenerator Air Compressor Proportioner Control PanelAdvanced Display Module ADM, Engine Control Module,Call Button Function Out Advanced Display Module ADMRed Random Flashing or Solid Module error exists System Status Indicator B ConditionsUSB Module Status LEDs CL Conditions Module Status LEDs CN ConditionsMenu Bar Power Up ScreenSoft Keys Navigation within ScreensIcons See Errors, page 51 for moreIcons Function Softkeys Icon FunctionMotor Control Module MCM MCM Rotary Switch PositionsIcon Description Function Engine Control ModuleColor Load CenterRelated Component Advanced Display Module ADM, page 19, CN for conditions Temperature Control ModulesLow Power Module Lptcm Cable Connections Hptcm a and B Rotary Switch Settings Adjust Rotary SwitchSetting Zone Lptcm a and B Rotary Switch SettingsSize Component Circuit BreakersMCM See Circuit Breaker Configuration Options,Disable LPTCMs For Booster Heat Auxiliary Wiring Diagram OptionsCircuit Breaker Configuration Options Size Component CB10 90 a 120/240V AlternatorOverview Overview HE VB HE VA Locate Reactor SetupTrailer Setup Guidelines, page 35 for instructions Setup Trailer Setup Guidelines Install Wall optional Top View With Wall Side View With Wall General Equipment Guidelines Connect BatteryAdd Fuel Breathing Air Electrical ConnectionsConnect Feed Pumps Connect Heated Hose Install Fluid Temperature SensorConnect Pressure Relief Lines Pressure Check Hose Connect Whip Hose to Gun Or Gun Fluid ManifoldConnect Remote Display Module GroundingSupply Wet Cups With Throat Seal Liquid TSL Advanced Screen 3- USB, Advanced Display Module ADM OperationSet Password Setup ModeSetup Screens Navigation Diagram Figure Advanced Screen 1 General Advanced Setup ScreensAdvanced Screen 3 USB Advanced Screen 2 UnitsSystem Enable or Disable RecipesRecipes Add RecipeRun Mode Run Screens Navigation Diagram Home System Off Home System With ErrorHome System Active TargetsErrors MaintenanceCycles EventsDiagnostic Recipes TroubleshootingSystem Events Startup Load fluid with feed pumps Check coolant colorOpen the main air shutoff valve Setup ADM. Advanced Display Module ADM Operation, Temporary Manual Hose Temperature Control Follow Startup, Fluid CirculationCirculation Through Reactor Gun Manual Jog ModeCirculation Through Gun Manifold Fusion AP gun is shown SprayingSpray Adjustments Shutdown Pressure Relief Procedure,Pressure Relief Procedure Flushing FlushingProportioner Maintenance MaintenanceEvery 500 Service Hours or 1 Year Engine MaintenanceFuel Tank Flush Inlet Strainer ScreenPump Lubrication System Follow Pressure Relief Procedure,Perform Shutdown, Drain CoolantRefill Proportioner Coolant Loop, LED Component LED ColorRefill Proportioner Coolant Loop Maintenance Coolant Specifications Refill Engine Coolant LoopTroubleshoot Errors ErrorsView Errors Error Codes and Troubleshooting TroubleshootingError Type Name Cause Solution Code Location A1NM MCM AlarmA4CH A4CM MCM AlarmA4DA A4DBA7CH A4NM MCM AlarmA7DA A7DBCacb CacaCach Cacm MCMDE0X MCM Alarm Dadx MCM AlarmF9DX MCM Alarm K8NM MCM AlarmP6AX MCM Alarm P4AX MCM AlarmMBN0 MCM Advi SoryError Type Name Cause Solution Code Position T2BE T2AEDeviation T2DB T2DAT2DH T2DET4CA T4CM MCM AlarmT4CB T4CHT4DH T4NM MCM AlarmT6BE T6AET6DA T6DBT8AE V4CM MCM Alarm V1CM MCM AlarmWbnm MCM Alarm T8DAMCM Alarm Wmce MCM AlarmWscx ADM Advisory Wsux USB AdvisoryUSB Data Follow Download Procedure, page 91, to retrieve log filesUSB Logs Event LogDaily Log System Configuration SettingsSystem Software Log Blackbox Log FileCustom Language File Download ProcedureCreate Custom Language Strings Upload ProcedureInformation Screens Appendix a Engine Control Module Run ScreensRun Screen Layout Information Screen LayoutIcon Description Details Mode IconsInstrumentation Icons Shutdown AlarmsDimensions Dimensions Pallet Mounting Dimensions Proportioners For Foam Performance ChartsProportioners For Coatings PressureFusion Mechanical Purge, Round Pattern Fusion Air Purge, Flat PatternFusion Mechanical Purge, Flat Pattern 30i Models Technical SpecificationsRecommended Air Compressors WeightNoise Fluid InletsXP2i Models 3A1705J 105 For Graco Canada Customers Graco Standard WarrantyGraco Information