Quinny 65040-AB manual To clear a particular sequence from the memory, press F1

Page 52

Section VIII - Power$ync II™ Operation

If the network is powered-up, but not running, or if there are only two machines on the network, the following message may be too quick to be seen.

PLEASE WAIT

TRANSFERRING NETWORK DATA TO

ALL ON-LINE COMPRESSORS

Press F2 to edit the networked pressure deadbands:

1>000U 000L 2>000U 000L 3>000U 000L 4>000U 000L 5>000U 000L 6>000U 000L

UP/DOWN DEADBAND, F1 EDIT, ENTER RETURN

When this screen is displayed, the unload and load pressure settings will be flashing for position number one. To edit position number one, press F1. The unload pressure setting will start flashing slowly, indicating that this number is ready to edit. Use the UP and DOWN arrow keys to change the setting. Once the correct setting has been specified, press ENTER to accept. The load pressure setting will now begin to flash slowly. Follow the same procedure to change the load pressure setting. When the unload and load pressure settings have been accepted, the control will flash both settings, indicating that you can now move to another position setting. To move to the second position, use the UP arrow key. Following the same procedure, adjust the unload and load pressures for all machines on the network. Press ENTER to transfer this data to all on-line compressors and return to Network Configuration Menu 3.

Press the UP arrow key to move to Network Configuration Menu 4. From this display, sequences and schedules can be cleared from all on-line networked compressors at one time, from one machine.

NETWORK CONFIGURATION MENU 4

CLEAR SEQUENCE ➔ PRESS F1

CLEAR SEQUENCE AND SCHEDULE ➔ PRESS F2 UP FOR NEXT MENU/DOWN FOR PREVIOUS MENU

To clear a particular sequence from the memory, press F1.

When F1 is pressed, the following display will appear:

NETWORK SEQUENCE ERASE

SEQUENCE NUMBER TO CLEAR ➔ 1

PRESS ENTER TO ACCEPT VALUE

Use the UP or DOWN arrow keys to scroll to the proper sequence number to clear. Once the proper sequence number is displayed, press ENTER.

The control will display a warning message to prevent the accidental erasure of a particular sequence. This warning message gives the option of continuing the process of erasing a sequence or aborting the process.

NOTICE

YOU HAVE SELECTED SEQUENCE 1 TO CLEAR

NOTICE

PRESS F1 TO CLEAR OR ENTER TO ABORT

Press either F1 or ENTER to complete the process and return the display to Network Configuration Menu 4.

To clear all sequence and schedule information from all compressors on the network, press F2.

NOTICE

YOU WILL CLEAR ALL SEQUENCE AND SCHEDULE

NOTICE

PRESS F1 TO CLEAR OR ENTER TO ABORT

Press either key to complete the process and return to Network Configuration Menu 4.

From Network Configuration Menu 4, press the UP arrow key to move to Network Configuration Menu 5.

NETWORK CONFIGURATION MENU 5

POINTER PASSING DELAY TIME (SECONDS) ___

ENTER ACCEPTS VALUE / EXITS MENU

Press the UP or DOWN key to increase or decrease this value. Press ENTER to return to the previous display.

50

Quincy Compressor® - QSD™

 

 

Page 51 Page 53
Image 52
Page 51 Page 53
Contents QSD Series Page Table of Contents Section V Maintenance or Service Preparation Standard Warranty Dimensional Data air-cooled Dimensional Data water-cooled Safety Precautions Section I GeneralSafety Alert Symbols Spare Parts Ordering InformationSection II Description General Description Compression Cycle and Air FlowCooling System Lubricating Fluid SystemMoisture Separator Water-cooledCapacity Control System Electrical System Back-up Control Shutdown ConditionsIndicators Safety SensorsMain Power on Light High Discharge Air Temperature LightsSection II Description Section III Installation Moving the Unit to the Installation SiteReceiving LocationPiping Connections Manual Shutoff Valve Piping Fit-upElectrical GuardsWater Flow Water QualityFluid Level Fan RotationSection IV Operating Procedures Prior to StartingStarting the Compressor Stopping the Compressor Normal OperationPressure Readings Temperature Readings Water-cooledStopping the Compressor Emergency Section V Preparing for Maintenance or Service This page Intentionally Left Blank Fluid Specifications SafetySection VI Servicing Air Filter Fluid LifePreparation for New Seal Installation Input Shaft SealSeal Installation Airend Sealing SystemSection VII Service Adjustments Pressure SwitchPressure Switch Back-up Operating Mode Adjusting Pressure SwitchThis page Intentionally Left Blank Section Viii Power$ync II Operation Introduction to Power$yncBack-up Mode Operation Do not switch modes with power on the compressorMultiple Machine Operational Mode Auto Dual Time DelaySingle Machine Operational Modes Continuous RunPressure Settings Network Load Delay TimeNetwork Installation Connecting Cable to the Power$ync II Circuit BoardRocker Switch Settings Network Setup Network Voltage Tests on Power$ync II SystemsUP/DOWN DEADBAND, F1 EDIT, Enter Return Power-up Displays Start-upSection Viii Power$ync II Operation Compressor in Back-up Mode U19 Memory Failure Contact Your Service RepresentativeU19 Data Checksum Error Press F2 to Update Deadband Data Error Press F1 to ClearU19 Data not Initialized Press F2 to Initialize Filter Needs Servicing Please Replace AS Soon AS Possible Start-up Displays Operational DisplaysAdditional Sensors Compressor is StartingCompressor is Unloaded Compressor is Unloaded Minutes Left to ShutdownProgrammed Shutdown Compressor Settings and Maintenance Displays Mode and Pressure DisplaysCompressor Mode of Operation Auto Dual Timed Stop Press F1 Press F2Read Pressure Settings pages 34-35 before Press F1 to change the load and unload pressuresPlease Wait Network Configuration in Progress Machine ID SetupMachine ID for this Compressor Press Enter to Accept Value Before setting or changing a sequence, read Sequence Network DataUP/DOWN POSITION, F1 EDIT, Enter Return UP/DOWN Machine ID, Enter ReturnDAY Monday SEQ Abcd Network Configuration MenuDAY Monday SEQ To clear a particular sequence from the memory, press F1 Filter Service Hourmeters Reset Service HourmetersCompressor Hourmeter Menu Compressor Hourmeters Intake Filter HoursPress F1 to Reset Fluid Filter Hours Press Enter to Return Fluid Filter Hours Reset to Press Enter to ReturnPress F1 to Reset Fluid Hours Press Enter to Return Fluid Hours Reset to Press Enter to ReturnCompressor Maintenance Menu Compressor Control Test Time Menu To View Current TimeTo SET Time and Date Time and Date Menu Current Time on this ControlHorsepower Compressor Control Test Menu Unload Valve Test Press F1Unload Press Fluid PressUnit Configuration Date Modem Baud Rate SetupCompressor Diagnostic Menu View Shutdown LOG Network DiagnosticSection Viii Power$ync II Operation ETOL00 FTOL00 Network Connection Data Confidence Modem INITIALIZATION** Init Indicator is lit, the indicator will remain litF1 to EDIT/ENTER to Accept Value Compressor has Shut Down Emergency Stop Button WAS Pressed Sequence Data Error Press F1 to Clear Schedule Data Error Compressor has Shut Down Take Corrective Action Back-up Mode until all faults have been corrected Inlet Temp Fluid Pressure STG 1 OUT Temp STG 2 in Temp Shutdown Log Messages Emergency Stop PressedMotor Overload STG 2 Discharge RTD Failure Control log has no entries at that point Section IX Troubleshooting Probable Causes Corrective Action Failure to StartSection IX Troubleshooting Unscheduled ShutdownProbable Causes Corrective Action Unscheduled Shutdown Frequent Air Cleaner Clogging High Discharge Air TemperatureProbable Causes Corrective Action Low Air Delivery Frequent Fluid Filter CloggingCompressor does not Unload when there is no Air Demand Too Rapid Cycling Between Load and Unload Pressure Relief Valve Exhausting Excessive Fluid in Buffing Air Vent BowlsWater in Buffing Air Vent Bowls Excessive Fluid in Gearbox Vent BowlLow Delivery Pressure High Interstage PressureErroneous Displays Microprocessor Will Not Display MessagesSection X- Maintenance Schedule Interval ActionDaily Operating Record Quincy Compressor QSD Quincy Compressor QSD
Top Page Image Contents