Quinny 65040-AB manual Compressor Hourmeter Menu Compressor Hourmeters, Filter Service Hourmeters

Page 53

Section VIII - Power$ync IIOperation

Press F2 at the Compressor Setup Menu to access the Maintenance Menus. There are four main Compressor Maintenance Menus that allow the operator to check or reset maintenance hourmeters, time and date, view diagnostics, and set modem baud rate. The operator can also access the compressor configuration information. Once in the Compressor Maintenance Menu, use the UP and DOWN arrow keys to move between menus. Compressor Maintenance Menu 1 contains maintenance hourmeters and time and date information.

COMPRESSOR MAINTENANCE MENU 1

MAINTENANCE HOURMETERS PRESS F1

TIME AND DATE PRESS F2

UP FOR NEXT MENU/DOWN FOR PREVIOUS MENU

To access maintenance hourmeters, press F1. To move to another maintenance menu, press the UP arrow key.

The Compressor Hourmeter Menu allows access to compressor hourmeters that include loaded hours, unloaded hours, lubricant hours, line filter hours, intake filter hours, and lubricant filter hours. It also allows these hourmeters to be reset when maintenance is performed.

COMPRESSOR HOURMETER MENU

COMPRESSOR HOURMETERS

PRESS F1

FILTER SERVICE HOURMETERS

PRESS F2

RESET SERVICE HOURMETERS

PRESS F3

Press F1 to access loaded and unloaded, lubricant and line filter hourmeters. Press ENTER to return to the previous display.

LOADED HOURS _____ UNLOADED HOURS _____

HOURS SINCE LAST FLUID CHANGE _____

******************************************

PRESS ENTER TO RETURN

This display shows the number of hours that the compressor has been running at some load level and the number of hours that the compressor has been running unloaded. Logging these hourmeter readings will help determine if changes to sequence or schedule routines should be made in network applications. Logging fluid hours and comparing them to the results of the fluid analysis will allow the advance scheduling of fluid changes. Comparing fluid hours to analysis reports and temperature logs will also aid in diagnosing ambient conditions which might be shortening fluid life. Press ENTER to return to the hourmeter menu.

Press F2 at the Compressor Hourmeter Menu to access the filter hourmeters.

INTAKE FILTER HOURS _________

LINE FILTER HOURS ____________

*******************************

PRESS ENTER TO RETURN

Inlet filter, and fluid filter hours can be logged to help anticipate preventative maintenance. Line filter hours refers to the control line filter that assures clean air to the pneumatic controls on the compressor package. This hourmeter is a reminder that, although there is no element to change and the filter automatically drains, its operation should be checked periodically. An improperly operating control line filter will affect the proper operation of the compressor controls. Press ENTER to return to the Compressor Hourmeter Menu.

Quincy Compressor® - QSD™

51

 

 

Image 53
Contents QSD Series Page Table of Contents Section V Maintenance or Service Preparation Standard Warranty Dimensional Data air-cooled Dimensional Data water-cooled Section I General Safety PrecautionsSpare Parts Ordering Information Safety Alert SymbolsSection II Description Compression Cycle and Air Flow General DescriptionLubricating Fluid System Cooling SystemMoisture Separator Water-cooledCapacity Control System Electrical System Shutdown Conditions Back-up ControlSafety Sensors IndicatorsMain Power on Light High Discharge Air Temperature LightsSection II Description Moving the Unit to the Installation Site Section III InstallationReceiving LocationPiping Connections Piping Fit-up Manual Shutoff ValveGuards ElectricalWater Quality Water FlowFan Rotation Fluid LevelPrior to Starting Section IV Operating ProceduresStarting the Compressor Stopping the Compressor Normal OperationStopping the Compressor Emergency Temperature Readings Water-cooledPressure Readings Section V Preparing for Maintenance or Service This page Intentionally Left Blank Section VI Servicing SafetyFluid Specifications Fluid Life Air FilterInput Shaft Seal Preparation for New Seal InstallationAirend Sealing System Seal InstallationPressure Switch Section VII Service AdjustmentsPressure Switch Back-up Operating Mode Adjusting Pressure SwitchThis page Intentionally Left Blank Introduction to Power$ync Section Viii Power$ync II OperationBack-up Mode Operation Do not switch modes with power on the compressorAuto Dual Time Delay Multiple Machine Operational ModeSingle Machine Operational Modes Continuous RunNetwork Load Delay Time Pressure SettingsConnecting Cable to the Power$ync II Circuit Board Network InstallationRocker Switch Settings UP/DOWN DEADBAND, F1 EDIT, Enter Return Network Voltage Tests on Power$ync II SystemsNetwork Setup Start-up Power-up DisplaysSection Viii Power$ync II Operation U19 Memory Failure Contact Your Service Representative Compressor in Back-up ModeU19 Data not Initialized Press F2 to Initialize Deadband Data Error Press F1 to ClearU19 Data Checksum Error Press F2 to Update Filter Needs Servicing Please Replace AS Soon AS Possible Operational Displays Start-up DisplaysAdditional Sensors Compressor is StartingProgrammed Shutdown Compressor is Unloaded Minutes Left to ShutdownCompressor is Unloaded Mode and Pressure Displays Compressor Settings and Maintenance DisplaysCompressor Mode of Operation Auto Dual Timed Stop Press F1 Press F2Press F1 to change the load and unload pressures Read Pressure Settings pages 34-35 beforeMachine ID for this Compressor Press Enter to Accept Value Machine ID SetupPlease Wait Network Configuration in Progress Sequence Network Data Before setting or changing a sequence, readUP/DOWN POSITION, F1 EDIT, Enter Return UP/DOWN Machine ID, Enter ReturnDAY Monday SEQ Network Configuration MenuDAY Monday SEQ Abcd To clear a particular sequence from the memory, press F1 Reset Service Hourmeters Filter Service HourmetersCompressor Hourmeter Menu Compressor Hourmeters Intake Filter HoursFluid Filter Hours Reset to Press Enter to Return Press F1 to Reset Fluid Filter Hours Press Enter to ReturnPress F1 to Reset Fluid Hours Press Enter to Return Fluid Hours Reset to Press Enter to ReturnTime Menu To View Current Time Compressor Maintenance Menu Compressor Control TestTo SET Time and Date Time and Date Menu Current Time on this ControlCompressor Control Test Menu Unload Valve Test Press F1 HorsepowerUnload Press Fluid PressModem Baud Rate Setup Unit Configuration DateCompressor Diagnostic Menu View Shutdown LOG Network DiagnosticSection Viii Power$ync II Operation ETOL00 FTOL00 Network Connection Data Confidence F1 to EDIT/ENTER to Accept Value Indicator is lit, the indicator will remain litModem INITIALIZATION** Init Compressor has Shut Down Emergency Stop Button WAS Pressed Sequence Data Error Press F1 to Clear Schedule Data Error Compressor has Shut Down Take Corrective Action Back-up Mode until all faults have been corrected Inlet Temp Fluid Pressure STG 1 OUT Temp STG 2 in Temp Emergency Stop Pressed Shutdown Log MessagesMotor Overload STG 2 Discharge RTD Failure Control log has no entries at that point Probable Causes Corrective Action Failure to Start Section IX TroubleshootingUnscheduled Shutdown Section IX TroubleshootingProbable Causes Corrective Action Unscheduled Shutdown High Discharge Air Temperature Frequent Air Cleaner CloggingProbable Causes Corrective Action Low Air Delivery Frequent Fluid Filter CloggingCompressor does not Unload when there is no Air Demand Too Rapid Cycling Between Load and Unload Excessive Fluid in Buffing Air Vent Bowls Pressure Relief Valve ExhaustingWater in Buffing Air Vent Bowls Excessive Fluid in Gearbox Vent BowlHigh Interstage Pressure Low Delivery PressureMicroprocessor Will Not Display Messages Erroneous DisplaysInterval Action Section X- Maintenance ScheduleDaily Operating Record Quincy Compressor QSD Quincy Compressor QSD