Craftsman 572.61096, 572.61083 Shaftlock Collet, Wrench T Collet Toloosencollet, Keylesschuck

Page 10

_Always unplug rotary tool

before changing acces-

sories, changing collets or servicing your rotary tool.

I

SHAFTLOCK

COLLET

BUTTON_

WRENCH T

COLLET

TOLOOSENCOLLET

COLLETIDENTIFICATIONCHART-- Colletsizes ca_

beidentified by the rings on thebackend of collet./

1/32" C0llet hasone (1)

ring.

1/16" C011ethastwo (2)

rings.

3/32" C011ethas three (3) rings.

1/8 "Collet hasno rings.

J

KEYLESSCHUCK

COLLET --To loosen, first press shaft lock button and rotate the shaft by hand until the

lock engages the shaft preventing further rotation.

Do not engage lock while the Rotary Tool is running.

With the shaft lock engaged use the collet wrench to loosen the collet nut if necessary. Change accessories by inserting the new one into the collet as far as possible to minimize runout and unbalance. With the shaft lock engaged, finger tighten the collet nut until the accessory shank is gripped by the collet. Avoid excessive tightening of the collet nut. The collet system is a superior method of securing accessories.

COLLETS -- Two different size collets (see illustration), to accommodate different shank sizes, are available for your Rotary Tool. To install a different collet, remove the collet nut and remove the old collet. Insert the unslotted end of the collet in the hole in the end of the tool shaft. Replace collet nut on the shaft. Always use the collet which matches the shank size of the accessory

you plan to use. Never force a larger diameter shank into a collet.

BALANCING ACCESSORIES --For

precision work, it is important that all accessories be in good balance (much the same as the tires on your automobile). To true up or balance an accessory, slightly loosen collet nut and give the accessory Or

collet a 1/4 turn. Retighten collet nut and run the Rotary Tool. You should be able to tell by the sound and feel if your accessory is running in balance. Continue adjusting in this fashion until best balance is achieved. To maintain balance on abrasive wheel points, before each use, with the wheel point secured in the collet, turn on the Rotary Tool and run the Dressing Stone lightly against the revolving wheel point. This removes high

spots and trues up the wheel point for good balance.

The hanger is provided for the use of hanging your tool while using the flex-shaft or for storage. If you do not use the hanger, remove it from the tool and snap it back into place underneath the cord so it will be out of the way while the tool is in use.

Remember, your new Craftsman Rotary Tool is the finest power tool of its kind. But its

performance is only as good as the accessories with which it is used.

We recommend only Craftsman

accessories be used. Use of any other accessories may create a hazard. We hope you'll enjoy many years of trouble free

pleasure from your Sears Craftsman Rotary Power Toot.

lO

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Crrftsmrn Model Nos .610830 572.610950FullOne Year Warranty on Craftsman Rotary Power Tool Sears, Roebuck and Co., Dept WA, Hoffman Estates, ILWork Area Do not use tool if switch does not turn it Tool service must be performed only byPage Page Rbrc TM RotaryTool 610830 RotaryToolColet Flex-ShaftWrench T Collet Toloosencollet Shaftlock ColletKeylesschuck Page Page This blocks Models 610960 Rotary Tools have an Operatjn G SpeedsSpeed control should never be used with these tools Brushing Pressure Driver Motor CAP Shaft Flexible Ihousing CAP ColletCOLLET,I Drywall Cutting Bit For use in drywall Do not operate the flexible shaft with a sharpDescription Not for USE on Floor TileGrout Removal Kit GroutRemoval AttachmentCuttingDepth AdjustmentTo set cuttingdepth GroutRemoval Safety Warnings Attachmentcan becomehot afte Right AngleAttachment53002Donot over tightendrive adapter. Tighten the driveadapter ProlongusageQMUSTMATCHOFHOUStNGCURVATURE Maintenance Replaceable Brushes Models 610830, 610960Carbon Brushes BearingsExtension Cords 100 150 120Small Screw Mandrel No MandrelsScrew Mandrel No Small Engraving CuttersWire Brushes Polishing AccessoriesSanding Accessories Silicon Carbide Grinding StonesOperation it may fly off and strike you or bystanders 1olO Op2-4 572.610830,572.610960 Descripcion Numero DE PiezaDescription Portaherramienta de 3,2 mmLlave de tuerca no incluida Portaherramienta no incluidaNLcleodel eje flexible Tapa del impulsorCode no Description Descripcion NO. Decode NO. DE LapieceServicio de garantfa Indice PdginaSears, Roebuckand Co., Dept.817WA, HoffmanEstates, IL Conserveestasinstrucciones ControlSepa la ubicaciondel interrupter.AI dejar la Desprenderndurante el tiempo de rodaje Ierto polvogenerado per el Lijado, aserrado, amolado yVVoltio Herramienta Giratoria 610830 Herramienta GiratoriaJuego de Eje flexibleCortadoresmultiuso Cuadrode Identificacionde Portaherra Mandrilde Aprietesin LLAVEEl mandril de El use del mandrilde aprietePage Cubrirlasaberturasde ventilaci6nconla mano.Esto UTILIZACI6NDELAHERRAMIENTAMEC,4NICAGIRATORIACuandoaganela herramienla,tengacuidadode no Bloqueaelflujode airey hacequeel motorserecalienteNecesidadesdevelocidadesmaslentas Correcto PresiondecepilladoIncofirecto Jeflexible ProtectoraTuercadel \ PORTAHERRAMIENTA\ Tapadel Ejedel PortaherramientaLa guia de corte Noutilice el eje flexible con uea curvapronunciadaAC6moajustar la profundidadde corte AI Limpiar Lechada JuegoparaquitarlechadaAI Quitar lecharla para Remplazar una Baldosa Rota Page Noapriete excesivamenteel adaptadorde accionamienta Eladitamentopuede calentarsedespusdel usa ProlongadoEscobillasdecarbon EscobillaCordonesde extensi6n Vstagode lornillo No Cortadoresde grabar pequefiosVslagos Vstagode tornillopequeiloNoCepillosde alambre Accesoriospara lijarPage 61I -1f MAEAILA.OAOLAMINADOSPLASTIC0A I1 Acero 800-4-1MIY-HOiMIES1-800-469-4663
Top Page Image Contents