Craftsman Essential Guidelines for Safe Operation of Power Hammer Tools and Flex-Shafts

Page 17

Do not operate the flexible shaft with a sharp

bend (A). This can generate excessive heat and will reduce tool and flex-shaft life. The

recommended minimum is 6" radius (El). Contents of 53033 Flex-shaft Attachment

Description

1Flex-Shaft Assembly (42" long)

1Driver Cap

Cutting Guide53141

The cutting guide (sold separately) comes completely assembled and ready to use. For use in a variety of materials up to 3/4" thick. Match the bit type to the material to be cut. Always hold the tool firmly, using slow

53134

Drywall Cutting Bit

For use in drywall.

• When inserting the 53134 bit into your Craftsman Rotary tool, make sure that the bit has been inserted as far as possible.

=When making freehand cuts in drywall, - ex., repairing a hole in drywall. When using a template (outlet box) behind the drywall,

use the Drywall Cutting Bit 53134, cutting

in a counter-clockwise direction.

53135

Multipurpose Cutting Bit

For use in wood, plastics, drywall,

fiberglass, vinyl or aluminum siding, acoustical tile and laminates.

When inserting the 53135 bit into your Craftsman Rotary tool, make sure that the bit has been inserted as far as possible.

When making freehand cuts in use the

Multipurpose Cutting Bit 53135, cutting in a clockwise direction.

A.B.

steady pressure to make cuts.

To attach, follow the four steps shown below.

Important: Always cut in a clockwise direction, except when following a

template (outlet box), then cut in a

counterclockwise direction,

When using 53135, Multipurpose Cutting Bit, start the bit into the material at a 45 degree angle and then slowly bring it to a 90 degree angle to begin the cut.

53136

Tile Cutting Bit (Not Included)

For use on wall tile, cement board and plaster

When inserting the 53136 bit into your Craftsman Rotary tool, it is very important that 1/16"-1/8" of smooth shank remains visible above the cotlet.

When using 53136, Tile Cutting Bit, start the bit into the material at a 45 degree angle and then slowly bring it to a 90 degree angle to begin the cut.

NOT FOR USE ON FLOOR TILE

17

Image 17
Contents Model Nos .610830 572.610950 CrrftsmrnSears, Roebuck and Co., Dept WA, Hoffman Estates, IL FullOne Year Warranty on Craftsman Rotary Power ToolWork Area Tool service must be performed only by Do not use tool if switch does not turn itPage Page Rbrc TM RotaryTool RotaryTool 610830Flex-Shaft ColetKeylesschuck Shaftlock ColletWrench T Collet Toloosencollet Page Page This blocks Speed control should never be used with these tools Operatjn G SpeedsModels 610960 Rotary Tools have an Brushing Pressure COLLET,I Ihousing CAP ColletDriver Motor CAP Shaft Flexible Description Do not operate the flexible shaft with a sharpDrywall Cutting Bit For use in drywall Not for USE on Floor TileTo set cuttingdepth GroutRemoval AttachmentCuttingDepth AdjustmentGrout Removal Kit GroutRemoval Safety Warnings Donot over tightendrive adapter. Tighten the driveadapter Right AngleAttachment53002Attachmentcan becomehot afte ProlongusageCarbon Brushes Maintenance Replaceable Brushes Models 610830, 610960QMUSTMATCHOFHOUStNGCURVATURE Bearings100 150 120 Extension CordsScrew Mandrel No MandrelsSmall Screw Mandrel No Small Engraving CuttersSanding Accessories Polishing AccessoriesWire Brushes Silicon Carbide Grinding StonesOperation it may fly off and strike you or bystanders 1olO Op2-4 572.610830,572.610960 Description Numero DE PiezaDescripcion Portaherramienta de 3,2 mmNLcleodel eje flexible Portaherramienta no incluidaLlave de tuerca no incluida Tapa del impulsorDescription Descripcion NO. Decode NO. DE Lapiece Code noSears, Roebuckand Co., Dept.817WA, HoffmanEstates, IL Indice PdginaServicio de garantfa Control ConserveestasinstruccionesSepa la ubicaciondel interrupter.AI dejar la Desprenderndurante el tiempo de rodaje Lijado, aserrado, amolado y Ierto polvogenerado per elVVoltio Herramienta Giratoria Herramienta Giratoria 610830Cortadoresmultiuso Eje flexibleJuego de Cuadrode Identificacionde Portaherra El use del mandrilde apriete Mandrilde Aprietesin LLAVEEl mandril dePage Cuandoaganela herramienla,tengacuidadode no UTILIZACI6NDELAHERRAMIENTAMEC,4NICAGIRATORIACubrirlasaberturasde ventilaci6nconla mano.Esto Bloqueaelflujode airey hacequeel motorserecalienteNecesidadesdevelocidadesmaslentas Incofirecto PresiondecepilladoCorrecto Tuercadel \ PORTAHERRAMIENTA\ Tapadel Ejedel ProtectoraJeflexible PortaherramientaNoutilice el eje flexible con uea curvapronunciadaA La guia de corteAI Quitar lecharla para Remplazar una Baldosa Rota JuegoparaquitarlechadaC6moajustar la profundidadde corte AI Limpiar Lechada Page Eladitamentopuede calentarsedespusdel usa Prolongado Noapriete excesivamenteel adaptadorde accionamientaEscobilla EscobillasdecarbonCordonesde extensi6n Vslagos Cortadoresde grabar pequefiosVstagode lornillo No Vstagode tornillopequeiloNoAccesoriospara lijar Cepillosde alambrePage 61I -1f MAEAILA.OAOLAMINADOSPLASTIC0A I1 Acero 800-4-1MIY-HOiMIES1-800-469-4663