DeWalt D28115R instruction manual and 5 Sanding Flap Discs, Operation

Page 10

4-1/2" and 5" Sanding Flap Discs

3. With the guard latch open, rotate the

guard (D) into the desired working

English

Type 27 guard

hubbed sanding

flap disc

Type 27 guard

Quick-Change

backing flange

non-hubbed sanding

flap disc

threaded clamp nut

	position. The guard body should be
	positioned between the spindle and the
	operator to provide maximum operator	D
	protection.	D
	protection.

4.Close the guard latch to secure the guard

on the gear case. You should not be able to rotate the guard by hand when the latch is closed. Do not operate the grinder with a loose guard or the clamp lever in open position.

5.To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned and pull up on the guard.

NOTE: The guard is pre-adjusted to the diameter of the gear case hub at the factory. If, after a period of time, the guard M becomes loose, tighten the adjusting screw (M) with clamp lever in the closed position.

CAUTION: Do not tighten the adjusting screw with the clamp lever in open position. Undetectable damage to the guard or the mounting hub may result.

CAUTION: If guard cannot be tightened by adjusting clamp, do not use tool and take the tool and guard to a service center to repair or replace the guard.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

9

Image 10

Contents Guide D’UTILISATION Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsWork Area Service Additional Specific Safety Instructions for GrindersPersonal Safety Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of Kickback Components Fig Intended USERotating the Gear Case Assembly and AdjustmentsAccessories Mounting Guard2 and 5 Grinding Wheels 2 and 5 Cutting Wheels Wire WheelsSanding Discs 2 and 5 Sanding Flap Discs OperationGuards and Flanges Trigger SwitchSpindle Lockc Mounting and Removing Hubbed Wheels Mounting NON-HUBBED WheelsSurface Finishing with Sanding Flap Discs Surface Grinding with Grinding WheelsMounting Sanding Backing Pads Using Sanding Backing Pads Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Using Cutting Wheels MaintenanceCleaning Mounting Cutting WheelsYear Free Service Accessories RepairsThree Year Limited Warranty DAY Money Back GuaranteeEspace DE Travail Règles générales de sécurité pour tous les outilsConserver CES Directives Sécurité EN Matière D’ÉLECTRICITÉSécurité Personnelle Utilisation ET Entretien DE L’OUTILRéparation Causes de l’effet de rebond et prévention par l’opérateur NIOSH/OSHA/MSHA Composants Fig Rotation du carter d’engrenage AccessoiresAssemblage ET Réglages Assemblage du capot protecteurFonctionnement RemarqueCapot protecteur pour Meule de type Brosses métallique à touret Disques abrasifs Détente Dispositif DE Verrouillage DE LA Broche Bouton DE VerrouillageAssemblage ET Retrait DES Meules À Moyeu Intégré Assemblage DE Meules Sans Moyeu Meulage DE Surface Avec DES Meules AbrasivesMeulage DE Chant Avec DES Meules Abrasives Finition DE Surface Avec DES Disques DE Ponçage À LamellesAssemblage DES Tampons Pour LE Ponçage Utilisation DES Tampons Pour LE PonçageAssemblage et utilisation de disques de coupe type Assemblage DU Capot Protecteur Fermé Type Assemblage DE Disques DE CoupeGraissage EntretienNettoyage Utilisation DE Disques DE CoupeGarantie limitée trois ans Service D’ENTRETIEN Gratuit DE 1 ANRéparations Garantie DE Remboursement DE 90 JoursÁrea DE Trabajo Normas generales de seguridad para todas las herramientasConserve Estas Instrucciones Seguridad EléctricaSeguridad Personal USO Y Cuidado DE LA HerramientaMantenimiento Causas del retroceso y su prevención por parte del operador Utilice Siempre Equipos DE Seguridad Certificados Componentes Fig USO PrevistoAccesorios Ensamblado Y AjustesRotación de la caja de engranajes Protector de montajeFuncionamiento Protectores y bridasDiscos de esmerilar de 114 mm 4-1/2 y 127 mm De 152 mm Discos de alambre Discos de corte de 114 mmDiscos de lijar Discos de lijar de 114 mm 2 y 127 mm Interruptor disparador Botón DE BloqueoMontaje Y Extracción DE Discos CON Cubo Bloqueo DEL EJEMontaje DE Discos SIN Cubo Esmerilado DE Bordes CON Discos DE Esmerilar Esmerilado DE Superficie CON Discos DE EsmerilarAcabado DE Superficies CON Discos DE Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje DE Cepillos DE Alambre Y Discos DE Alambre Montaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte USO DE Ruedas DE CorteLubricación MantenimientoLimpieza ReparacionesExcepciones Póliza de GarantíaGarantía limitada de tres años Servicio Gratuito DE 1 AÑOGarantía DE Reembolso DE Dinero DE 90 Días Especificaciones D28065, D28065N, D28115, D28115NPage Page