DeWalt D28115R Assembly and Adjustments, Rotating the Gear Case, Accessories, Mounting Guard

Page 7

ASSEMBLY AND ADJUSTMENTS

ATTACHING SIDE HANDLE

 

The side handle (I) can be fitted to either side of

I

the gear case in the threaded holes, as shown.

 

Before using the tool, check that the handle

 

is tightened securely. Use a wrench to firmly

 

tighten the side handle.

 

Rotating the Gear Case

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect

tool from power source before making any adjustments or removing/installing attachments or accessories. Before recon- necting the tool, depress and release the trigger switch to ensure that the tool is off.

1.Remove guard and flanges from tool.

2.Remove the four corner screws attaching the gear case to motor housing.

3.Separating the gear case from motor housing not more than 1/4" (6.35 mm), rotate the gear case head to desired position. NOTE: If the gear case and motor housing become separated by more than 1/4" (6.35 mm), the tool must be serviced and re-assembled by a DEWALT service center. Failure to have the tool serviced may cause brush, motor and bearing failure.

4.Re-install screws to attach the gear case to the motor housing. Tighten screws to 18 in./lbs. (2.03 Nm) torque. Overtightening could cause screws to strip.

5.Re-install guard and correct flanges for the appropriate accessories.

Accessories

It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. See pages 7–9 for information on choosing the correct accessories.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other acces- sories running over rated accessory speed may burst and cause injury. Threaded accessories must have a 5/8"-11 hub. Every unthreaded accessory must have a 7/8" (22.2 mm) arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 7–9 of this manual. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

Mounting Guard

MOUNTING AND REMOVING GUARD

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

CAUTION: Guards must be used with all grinding wheels, sand- ing flap discs, wire brushes, and wire wheels. The tool may be used without a guard only when sanding with conventional sanding discs. Some DEWALT models are provided with a guard intended for use with depressed center wheels (Type 27) and hubbed grinding wheels (Type 27). The same guard is designed for use with sanding flap discs (Type 27 and 29) and wire brushes. Grinding and cutting with wheels other than Type 27 and 29 require different accessory guards not included with tool. Mounting instructions for these accessory guards are included in the accessory package.

1.

Open the guard latch (J). Align

K

 

the lugs (K) on the guard with the

 

 

slots (L) on the gear case.

 

2.

Push the guard down until the

 

 

guard lugs engage and rotate

L

 

freely in the groove on the gear

case hub.

J

 

English

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Guide D’UTILISATION Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsWork Area Tool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety Service Always Wear EYE Protection When Using this Tool Causes and Operator Prevention of Kickback Intended USE Components FigMounting Guard Assembly and AdjustmentsAccessories Rotating the Gear Case2 and 5 Grinding Wheels 2 and 5 Cutting Wheels Wire WheelsSanding Discs Operation 2 and 5 Sanding Flap DiscsGuards and Flanges Trigger SwitchSpindle Lockc Mounting NON-HUBBED Wheels Mounting and Removing Hubbed WheelsSurface Finishing with Sanding Flap Discs Surface Grinding with Grinding WheelsMounting Sanding Backing Pads Using Sanding Backing Pads Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Mounting Cutting Wheels MaintenanceCleaning Using Cutting WheelsDAY Money Back Guarantee Accessories RepairsThree Year Limited Warranty Year Free ServiceSécurité EN Matière D’ÉLECTRICITÉ Règles générales de sécurité pour tous les outilsConserver CES Directives Espace DE TravailUtilisation ET Entretien DE L’OUTIL Sécurité PersonnelleRéparation Causes de l’effet de rebond et prévention par l’opérateur NIOSH/OSHA/MSHA Composants Fig Assemblage du capot protecteur AccessoiresAssemblage ET Réglages Rotation du carter d’engrenageRemarque FonctionnementCapot protecteur pour Meule de type Brosses métallique à touret Disques abrasifs Détente Dispositif DE Verrouillage DE LA Broche Bouton DE VerrouillageAssemblage ET Retrait DES Meules À Moyeu Intégré Meulage DE Surface Avec DES Meules Abrasives Assemblage DE Meules Sans MoyeuFinition DE Surface Avec DES Disques DE Ponçage À Lamelles Meulage DE Chant Avec DES Meules AbrasivesUtilisation DES Tampons Pour LE Ponçage Assemblage DES Tampons Pour LE PonçageAssemblage et utilisation de disques de coupe type Assemblage DE Disques DE Coupe Assemblage DU Capot Protecteur Fermé TypeUtilisation DE Disques DE Coupe EntretienNettoyage GraissageGarantie DE Remboursement DE 90 Jours Service D’ENTRETIEN Gratuit DE 1 ANRéparations Garantie limitée trois ansSeguridad Eléctrica Normas generales de seguridad para todas las herramientasConserve Estas Instrucciones Área DE TrabajoUSO Y Cuidado DE LA Herramienta Seguridad PersonalMantenimiento Causas del retroceso y su prevención por parte del operador Utilice Siempre Equipos DE Seguridad Certificados USO Previsto Componentes FigProtector de montaje Ensamblado Y AjustesRotación de la caja de engranajes AccesoriosProtectores y bridas FuncionamientoDiscos de esmerilar de 114 mm 4-1/2 y 127 mm De 152 mm Discos de alambre Discos de corte de 114 mmDiscos de lijar Botón DE Bloqueo Discos de lijar de 114 mm 2 y 127 mm Interruptor disparadorMontaje Y Extracción DE Discos CON Cubo Bloqueo DEL EJEMontaje DE Discos SIN Cubo Esmerilado DE Superficie CON Discos DE Esmerilar Esmerilado DE Bordes CON Discos DE EsmerilarMontaje DE LAS Almohadillas DE Respaldo Para Lijar Acabado DE Superficies CON Discos DE LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje DE Cepillos DE Alambre Y Discos DE Alambre Montaje DEL Protector Cerrado Tipo Montaje y uso de discos de corte TipoUSO DE Ruedas DE Corte Montaje DE LOS Discos DE CorteReparaciones MantenimientoLimpieza LubricaciónServicio Gratuito DE 1 AÑO Póliza de GarantíaGarantía limitada de tres años ExcepcionesEspecificaciones D28065, D28065N, D28115, D28115N Garantía DE Reembolso DE Dinero DE 90 DíasPage Page
Top Page Image Contents