DeWalt D28115R instruction manual Guards and Flanges, Trigger Switch, Spindle Lockc

Page 11

Guards and Flanges

It is important to choose the correct guards and flanges to use with the grinder accessories. See pages 7–9 for the correct accessories.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Every unthreaded accessory must have a 7/8" (22.2 mm) arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 7–9. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

Trigger Switch

CAUTION: Hold the side handle and body of the tool firmly to maintain control of the tool at start up and during use and until the wheel or accessory stops rotating. Make sure the wheel has come to a complete stop before laying the tool down.

NOTE: To reduce unexpected tool movement, do not switch the tool on or off while under load conditions. Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down.

CAUTION: Before connecting the tool to a power source depress and release the trigger switch (A) once without depressing the lock-on button (Fig. 1, B) to ensure that the switch is off. Depress and release the trigger switch as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure.

To turn the tool on, depress the trigger switch (A). The tool will run while the switch is depressed. Turn the tool off by releasing the trigger switch.

LOCK-ON BUTTON (D28065, D28115)

 

 

The lock-on button (B) offers increased

 

 

comfort in extended use applications.

 

 

To lock the tool on, depress the trigger

 

 

switch (A), then push the lock-on button

 

 

(B). The tool will continue to run after

 

 

the trigger switch is released. To unlock

B

A

the tool, depress and release the trigger

 

 

switch. This will cause the tool to stop.

CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turning the tool off.

SPINDLE LOCKC

The spindle lock (C) is provided to prevent the spindle from rotating when installing or removing wheels. Operate the spindle lock only when

the tool is turned off, unplugged

from the power supply, and has come to a complete stop. Do not engage the

spindle lock while the tool is operating because damage to the tool will result. To engage the lock, depress the spindle lock button and rotate the spindle until you are unable to rotate the spindle further.

English

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Guide D’UTILISATION Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety Tool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety ServiceAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of Kickback Intended USE Components FigMounting Guard Assembly and AdjustmentsAccessories Rotating the Gear Case2 and 5 Grinding Wheels Sanding Discs Wire Wheels2 and 5 Cutting Wheels Operation 2 and 5 Sanding Flap DiscsSpindle Lockc Trigger SwitchGuards and Flanges Mounting NON-HUBBED Wheels Mounting and Removing Hubbed WheelsMounting Sanding Backing Pads Surface Grinding with Grinding WheelsSurface Finishing with Sanding Flap Discs Mounting Wire Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Sanding Backing Pads Mounting Closed Type 1 Guard Mounting and Using Cutting Type 1 WheelsUsing Wire CUP Brushes and Wire Wheels Mounting Cutting Wheels MaintenanceCleaning Using Cutting WheelsDAY Money Back Guarantee Accessories RepairsThree Year Limited Warranty Year Free ServiceSécurité EN Matière D’ÉLECTRICITÉ Règles générales de sécurité pour tous les outilsConserver CES Directives Espace DE TravailUtilisation ET Entretien DE L’OUTIL Sécurité PersonnelleRéparation Causes de l’effet de rebond et prévention par l’opérateur NIOSH/OSHA/MSHA Composants Fig Assemblage du capot protecteur AccessoiresAssemblage ET Réglages Rotation du carter d’engrenageRemarque FonctionnementCapot protecteur pour Meule de type Brosses métallique à touret Disques abrasifs Détente Assemblage ET Retrait DES Meules À Moyeu Intégré Bouton DE VerrouillageDispositif DE Verrouillage DE LA Broche Meulage DE Surface Avec DES Meules Abrasives Assemblage DE Meules Sans MoyeuFinition DE Surface Avec DES Disques DE Ponçage À Lamelles Meulage DE Chant Avec DES Meules AbrasivesUtilisation DES Tampons Pour LE Ponçage Assemblage DES Tampons Pour LE PonçageAssemblage et utilisation de disques de coupe type Assemblage DE Disques DE Coupe Assemblage DU Capot Protecteur Fermé TypeUtilisation DE Disques DE Coupe EntretienNettoyage GraissageGarantie DE Remboursement DE 90 Jours Service D’ENTRETIEN Gratuit DE 1 ANRéparations Garantie limitée trois ansSeguridad Eléctrica Normas generales de seguridad para todas las herramientasConserve Estas Instrucciones Área DE TrabajoUSO Y Cuidado DE LA Herramienta Seguridad PersonalMantenimiento Causas del retroceso y su prevención por parte del operador Utilice Siempre Equipos DE Seguridad Certificados USO Previsto Componentes FigProtector de montaje Ensamblado Y AjustesRotación de la caja de engranajes AccesoriosProtectores y bridas FuncionamientoDiscos de esmerilar de 114 mm 4-1/2 y 127 mm De 152 mm Discos de lijar Discos de corte de 114 mmDiscos de alambre Botón DE Bloqueo Discos de lijar de 114 mm 2 y 127 mm Interruptor disparadorMontaje DE Discos SIN Cubo Bloqueo DEL EJEMontaje Y Extracción DE Discos CON Cubo Esmerilado DE Superficie CON Discos DE Esmerilar Esmerilado DE Bordes CON Discos DE EsmerilarMontaje DE LAS Almohadillas DE Respaldo Para Lijar Acabado DE Superficies CON Discos DE LijarMontaje DE Cepillos DE Alambre Y Discos DE Alambre Montaje y uso de cepillos de alambre y discos de alambreUSO DE Almohadillas DE Respaldo Para Lijar Montaje DEL Protector Cerrado Tipo Montaje y uso de discos de corte TipoUSO DE Ruedas DE Corte Montaje DE LOS Discos DE CorteReparaciones MantenimientoLimpieza LubricaciónServicio Gratuito DE 1 AÑO Póliza de GarantíaGarantía limitada de tres años ExcepcionesEspecificaciones D28065, D28065N, D28115, D28115N Garantía DE Reembolso DE Dinero DE 90 DíasPage Page
Top Page Image Contents