DeWalt D28115R Maintenance, Cleaning, Mounting Cutting Wheels, Using Cutting Wheels

Page 16

English

guard by hand when the latch is in closed position. If rotation is pos- sible, tighten the adjusting screw (M) M with clamp lever in the closed position.

Do not operate grinder with a loose guard or clamp lever in open position.

5.To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned and pull up on the guard.

NOTE: If, after a period of time, the guard becomes loose, tighten the adjusting screw (M) with the clamp lever in the closed position.

CAUTION: Do not tighten adjusting screw with clamp lever in open position. Undetectable damage to guard or mounting hub may result.

MOUNTING CUTTING WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

CAUTION: Matching diameter backing flange and threaded clamp nut (included with tool) must be used for cutting wheels.

1.Place the unthreaded backing flange on spindle with the raised section (pilot) facing up. The raised section

(pilot) on the backing flange will be against the wheel when the wheel is installed.

2. Place the wheel on the quick-change backing flange, centering the wheel on the raised section (pilot).

3. Install the threaded clamp nut with the raised section (pilot) facing away from the wheel.

4. Depress the spindle lock button and tighten clamp nut with a wrench.

5.To remove the wheel, grasp and turn while depressing the spindle lock button.

USING CUTTING WHEELS

WARNING: Do not use edge grinding/ cutting wheels for surface grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage and injury may result.

1.Allow tool to reach full speed before touching tool to work surface.

2.Apply minimum pressure to work surface, allowing tool to operate at high speed. Cutting rate is greatest when the tool operates at high speed.

3.Once a cut is begun and a notch is established in the workpiece, do not change the angle of the cut. Changing the angle will cause the wheel to bend and may cause wheel breakage.

4.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before setting it down.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

Cleaning

WARNING: Blowing dust and grit out of motor and switch actuator using clean, dry compressed air is a necessary regular maintenance procedure. Dust and grit containing metal particles often accumulate on interior surfaces and could create an electrical shock or electrocution if not frequently cleaned out. It is recommended that a ground fault circuit interrupter (GFCI) is utilized to further protect the user from electric shock resulting from the accumulation of conductive particles. If the tool is deactivated by the GFCI, unplug the tool and

15

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Guide D’UTILISATION Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsWork Area Additional Specific Safety Instructions for Grinders Personal SafetyService Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of Kickback Components Fig Intended USEAssembly and Adjustments AccessoriesRotating the Gear Case Mounting Guard2 and 5 Grinding Wheels 2 and 5 Cutting Wheels Wire WheelsSanding Discs 2 and 5 Sanding Flap Discs OperationGuards and Flanges Trigger SwitchSpindle Lockc Mounting and Removing Hubbed Wheels Mounting NON-HUBBED WheelsSurface Finishing with Sanding Flap Discs Surface Grinding with Grinding WheelsMounting Sanding Backing Pads Using Sanding Backing Pads Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Maintenance CleaningUsing Cutting Wheels Mounting Cutting WheelsAccessories Repairs Three Year Limited WarrantyYear Free Service DAY Money Back GuaranteeRègles générales de sécurité pour tous les outils Conserver CES DirectivesEspace DE Travail Sécurité EN Matière D’ÉLECTRICITÉSécurité Personnelle Utilisation ET Entretien DE L’OUTILRéparation Causes de l’effet de rebond et prévention par l’opérateur NIOSH/OSHA/MSHA Composants Fig Accessoires Assemblage ET RéglagesRotation du carter d’engrenage Assemblage du capot protecteurFonctionnement RemarqueCapot protecteur pour Meule de type Brosses métallique à touret Disques abrasifs Détente Dispositif DE Verrouillage DE LA Broche Bouton DE VerrouillageAssemblage ET Retrait DES Meules À Moyeu Intégré Assemblage DE Meules Sans Moyeu Meulage DE Surface Avec DES Meules AbrasivesMeulage DE Chant Avec DES Meules Abrasives Finition DE Surface Avec DES Disques DE Ponçage À LamellesAssemblage DES Tampons Pour LE Ponçage Utilisation DES Tampons Pour LE PonçageAssemblage et utilisation de disques de coupe type Assemblage DU Capot Protecteur Fermé Type Assemblage DE Disques DE CoupeEntretien NettoyageGraissage Utilisation DE Disques DE CoupeService D’ENTRETIEN Gratuit DE 1 AN RéparationsGarantie limitée trois ans Garantie DE Remboursement DE 90 JoursNormas generales de seguridad para todas las herramientas Conserve Estas InstruccionesÁrea DE Trabajo Seguridad EléctricaSeguridad Personal USO Y Cuidado DE LA HerramientaMantenimiento Causas del retroceso y su prevención por parte del operador Utilice Siempre Equipos DE Seguridad Certificados Componentes Fig USO PrevistoEnsamblado Y Ajustes Rotación de la caja de engranajesAccesorios Protector de montajeFuncionamiento Protectores y bridasDiscos de esmerilar de 114 mm 4-1/2 y 127 mm De 152 mm Discos de alambre Discos de corte de 114 mmDiscos de lijar Discos de lijar de 114 mm 2 y 127 mm Interruptor disparador Botón DE BloqueoMontaje Y Extracción DE Discos CON Cubo Bloqueo DEL EJEMontaje DE Discos SIN Cubo Esmerilado DE Bordes CON Discos DE Esmerilar Esmerilado DE Superficie CON Discos DE EsmerilarAcabado DE Superficies CON Discos DE Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje DE Cepillos DE Alambre Y Discos DE Alambre Montaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte USO DE Ruedas DE CorteMantenimiento LimpiezaLubricación ReparacionesPóliza de Garantía Garantía limitada de tres añosExcepciones Servicio Gratuito DE 1 AÑOGarantía DE Reembolso DE Dinero DE 90 Días Especificaciones D28065, D28065N, D28115, D28115NPage Page
Top Page Image Contents