DeWalt D28115R Mounting and Using Wire Brushes and Wire Wheels, Using Sanding Backing Pads

Page 14

English

CAUTION: Proper guard must be reinstalled for grinding wheel, sanding flap disc, wire brush or wire wheel applications after sanding applications are complete.

1.Place or appropriately thread backing pad (O) on the spindle.

2.Place the sanding disc (P) on the backing pad.

3.While depressing spindle lock, thread clamp nut (H) on spindle, piloting the raised hub on the clamp nut into the center of sanding disc and backing pad.

4. Tighten the clamp nut by hand.

H

P

Then depress the spindle lock

 

 

 

button while turning the sanding

 

 

disc until the sanding disc and

 

 

clamp nut are snug.

 

 

5. To remove the wheel, grasp and

 

 

turn the backing pad and sanding

 

 

pad while depressing the spindle

 

 

lock button.

 

 

USING SANDING BACKING PADS

 

O

Choose the proper grit sandpaper for

 

 

your application. Sandpaper is available in various grits. Coarse grits yield faster material removal rates and a rougher finish. Finer grits yield slower material removal and a smoother finish.

Begin with coarse grit discs for fast, rough material removal. Move to a medium grit paper and finish with a fine grit disc for optimal finish.

Coarse

16 - 30 grit

Medium

36 - 80 grit

Fine Finishing

100 - 120 grit

Very Fine Finishing

150 - 180 grit

1.Allow the tool to reach full speed before touching tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Sanding rate is greatest when the tool operates at high speed.

3.Maintain a 5˚ to 15˚ angle between

the tool and work surface. The

 

sanding disc

should

contact

 

approximately

one inch

of work

5˚-15˚

surface.

 

 

 

 

 

4.Move the tool constantly in a straight

line to prevent burning and swirling of work surface. Allowing the tool to rest on the work surface without moving, or moving the tool in a circular motion causes burning and swirling marks on the work surface.

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

Mounting and Using Wire Brushes and Wire Wheels

Wire cup brushes or wire wheels screw directly on the grinder spindle without the use of flanges. Use only wire brushes or wheels provided with a 5/8"-11 threaded hub. A Type 27 guard is required when using wire brushes and wheels.

CAUTION: Wear work gloves when handling wire brushes and wheels. They can become sharp.

CAUTION: Wheel or brush must not touch guard when mounted or while in use. Undetectable damage could occur to the accessory, causing wires to fragment from accessory wheel or cup.

MOUNTING WIRE BRUSHES AND WIRE WHEELS

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

13

Image 14
Contents Guide D’UTILISATION Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety Service Additional Specific Safety Instructions for GrindersPersonal Safety Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of Kickback Components Fig Intended USERotating the Gear Case Assembly and AdjustmentsAccessories Mounting Guard2 and 5 Grinding Wheels Sanding Discs Wire Wheels2 and 5 Cutting Wheels 2 and 5 Sanding Flap Discs OperationSpindle Lockc Trigger SwitchGuards and Flanges Mounting and Removing Hubbed Wheels Mounting NON-HUBBED WheelsMounting Sanding Backing Pads Surface Grinding with Grinding WheelsSurface Finishing with Sanding Flap Discs Mounting Wire Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Sanding Backing Pads Mounting Closed Type 1 Guard Mounting and Using Cutting Type 1 WheelsUsing Wire CUP Brushes and Wire Wheels Using Cutting Wheels MaintenanceCleaning Mounting Cutting WheelsYear Free Service Accessories RepairsThree Year Limited Warranty DAY Money Back GuaranteeEspace DE Travail Règles générales de sécurité pour tous les outilsConserver CES Directives Sécurité EN Matière D’ÉLECTRICITÉSécurité Personnelle Utilisation ET Entretien DE L’OUTILRéparation Causes de l’effet de rebond et prévention par l’opérateur NIOSH/OSHA/MSHA Composants Fig Rotation du carter d’engrenage AccessoiresAssemblage ET Réglages Assemblage du capot protecteurFonctionnement RemarqueCapot protecteur pour Meule de type Brosses métallique à touret Disques abrasifs Détente Assemblage ET Retrait DES Meules À Moyeu Intégré Bouton DE VerrouillageDispositif DE Verrouillage DE LA Broche Assemblage DE Meules Sans Moyeu Meulage DE Surface Avec DES Meules AbrasivesMeulage DE Chant Avec DES Meules Abrasives Finition DE Surface Avec DES Disques DE Ponçage À LamellesAssemblage DES Tampons Pour LE Ponçage Utilisation DES Tampons Pour LE PonçageAssemblage et utilisation de disques de coupe type Assemblage DU Capot Protecteur Fermé Type Assemblage DE Disques DE CoupeGraissage EntretienNettoyage Utilisation DE Disques DE CoupeGarantie limitée trois ans Service D’ENTRETIEN Gratuit DE 1 ANRéparations Garantie DE Remboursement DE 90 JoursÁrea DE Trabajo Normas generales de seguridad para todas las herramientasConserve Estas Instrucciones Seguridad EléctricaSeguridad Personal USO Y Cuidado DE LA HerramientaMantenimiento Causas del retroceso y su prevención por parte del operador Utilice Siempre Equipos DE Seguridad Certificados Componentes Fig USO PrevistoAccesorios Ensamblado Y AjustesRotación de la caja de engranajes Protector de montajeFuncionamiento Protectores y bridasDiscos de esmerilar de 114 mm 4-1/2 y 127 mm De 152 mm Discos de lijar Discos de corte de 114 mmDiscos de alambre Discos de lijar de 114 mm 2 y 127 mm Interruptor disparador Botón DE BloqueoMontaje DE Discos SIN Cubo Bloqueo DEL EJEMontaje Y Extracción DE Discos CON Cubo Esmerilado DE Bordes CON Discos DE Esmerilar Esmerilado DE Superficie CON Discos DE EsmerilarAcabado DE Superficies CON Discos DE Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarMontaje DE Cepillos DE Alambre Y Discos DE Alambre Montaje y uso de cepillos de alambre y discos de alambreUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte USO DE Ruedas DE CorteLubricación MantenimientoLimpieza ReparacionesExcepciones Póliza de GarantíaGarantía limitada de tres años Servicio Gratuito DE 1 AÑOGarantía DE Reembolso DE Dinero DE 90 Días Especificaciones D28065, D28065N, D28115, D28115NPage Page