DeWalt D28115R Surface Grinding with Grinding Wheels, Surface Finishing with Sanding Flap Discs

Page 13

SURFACE GRINDING WITH GRINDING WHEELS

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

3.

Position yourself so that the open-underside of the wheel is

 

facing away from you.

4.

Once a cut is begun and a notch is established in the

 

workpiece, do not change the angle of the cut. Changing the

 

angle will cause the wheel to bend and may cause wheel

 

breakage. Edge grinding wheels are not designed to withstand

English

3.Maintain a 20˚ to 30˚ angle between the tool and work surface.

4.Continuously move the tool in a forward and back motion to avoid creating gouges in the work surface.

20˚-30˚

side pressures caused by bending.

5. Remove the tool from the work surface before turning the tool

off. Allow the tool to stop rotating before laying it down.

WARNING: Do not use edge grinding/cutting wheels for surface grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

EDGE GRINDING WITH GRINDING WHEELS CAUTION: Wheels used for cutting and edge grinding may break if they bend or twist while the tool is being used to do cut-off work

or deep grinding. To reduce the risk of serious injury, limit the use of these wheels with a standard Type 27 guard to shallow

cutting and notching [less than 1/2"

(12.7 mm) in depth]. The open side of the

guard must be positioned away from the operator. For deeper cutting with a Type 1 cut-off wheel, use a closed, Type 1 guard.

See the chart on page 8 for more information. Type 1 guards are available at extra cost from your local dealer or authorized service center.

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

and injury may result.

SURFACE FINISHING WITH SANDING FLAP DISCS

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to

 

operate at high speed. Sanding rate is greatest when the tool

 

operates at high speed.

 

3.

Maintain a 5˚ to 10˚ angle between

 

 

the tool and work surface.

 

4.

Continuously move the tool in a

5˚-10˚

 

forward and backward motion to

 

 

 

avoid creating gouges in the work

 

 

surface.

 

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

MOUNTING SANDING BACKING PADS

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Guide D’UTILISATION Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsWork Area Personal Safety Additional Specific Safety Instructions for GrindersService Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of Kickback Intended USE Components FigAccessories Assembly and AdjustmentsRotating the Gear Case Mounting Guard2 and 5 Grinding Wheels 2 and 5 Cutting Wheels Wire WheelsSanding Discs Operation 2 and 5 Sanding Flap DiscsGuards and Flanges Trigger SwitchSpindle Lockc Mounting NON-HUBBED Wheels Mounting and Removing Hubbed WheelsSurface Finishing with Sanding Flap Discs Surface Grinding with Grinding WheelsMounting Sanding Backing Pads Using Sanding Backing Pads Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Cleaning MaintenanceUsing Cutting Wheels Mounting Cutting WheelsThree Year Limited Warranty Accessories RepairsYear Free Service DAY Money Back GuaranteeConserver CES Directives Règles générales de sécurité pour tous les outilsEspace DE Travail Sécurité EN Matière D’ÉLECTRICITÉUtilisation ET Entretien DE L’OUTIL Sécurité PersonnelleRéparation Causes de l’effet de rebond et prévention par l’opérateur NIOSH/OSHA/MSHA Composants Fig Assemblage ET Réglages AccessoiresRotation du carter d’engrenage Assemblage du capot protecteurRemarque FonctionnementCapot protecteur pour Meule de type Brosses métallique à touret Disques abrasifs Détente Dispositif DE Verrouillage DE LA Broche Bouton DE VerrouillageAssemblage ET Retrait DES Meules À Moyeu Intégré Meulage DE Surface Avec DES Meules Abrasives Assemblage DE Meules Sans MoyeuFinition DE Surface Avec DES Disques DE Ponçage À Lamelles Meulage DE Chant Avec DES Meules AbrasivesUtilisation DES Tampons Pour LE Ponçage Assemblage DES Tampons Pour LE PonçageAssemblage et utilisation de disques de coupe type Assemblage DE Disques DE Coupe Assemblage DU Capot Protecteur Fermé TypeNettoyage EntretienGraissage Utilisation DE Disques DE CoupeRéparations Service D’ENTRETIEN Gratuit DE 1 ANGarantie limitée trois ans Garantie DE Remboursement DE 90 JoursConserve Estas Instrucciones Normas generales de seguridad para todas las herramientasÁrea DE Trabajo Seguridad EléctricaUSO Y Cuidado DE LA Herramienta Seguridad PersonalMantenimiento Causas del retroceso y su prevención por parte del operador Utilice Siempre Equipos DE Seguridad Certificados USO Previsto Componentes FigRotación de la caja de engranajes Ensamblado Y AjustesAccesorios Protector de montajeProtectores y bridas FuncionamientoDiscos de esmerilar de 114 mm 4-1/2 y 127 mm De 152 mm Discos de alambre Discos de corte de 114 mmDiscos de lijar Botón DE Bloqueo Discos de lijar de 114 mm 2 y 127 mm Interruptor disparadorMontaje Y Extracción DE Discos CON Cubo Bloqueo DEL EJEMontaje DE Discos SIN Cubo Esmerilado DE Superficie CON Discos DE Esmerilar Esmerilado DE Bordes CON Discos DE EsmerilarMontaje DE LAS Almohadillas DE Respaldo Para Lijar Acabado DE Superficies CON Discos DE LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje DE Cepillos DE Alambre Y Discos DE Alambre Montaje DEL Protector Cerrado Tipo Montaje y uso de discos de corte TipoUSO DE Ruedas DE Corte Montaje DE LOS Discos DE CorteLimpieza MantenimientoLubricación ReparacionesGarantía limitada de tres años Póliza de GarantíaExcepciones Servicio Gratuito DE 1 AÑOEspecificaciones D28065, D28065N, D28115, D28115N Garantía DE Reembolso DE Dinero DE 90 DíasPage Page
Top Page Image Contents