Bosch Power Tools 1994-6 Sanding Disc Assembly Backing PAD, To Install Backing PAD Sanding Disc

Page 12

! WARNING

BM 1609929T61 07-09:BM 1609929T61 07-09 7/8/09 1:37 PM Page 12

SANDING DISC ASSEMBLY

BACKING PAD

!WARNING Before attaching a backing pad be sure its maximum

safe operating speed is not exceeded by the nameplate speed of the tool.

!WARNING Wheel guard may not be used for most sanding

operations. Always reinstall wheel guard when converting back to grinding operations.

TO INSTALL BACKING PAD AND

SANDING DISC

Disconnect tool from power source. Attach hand guard (Fig. 1). Set the tool on its top side (spindle up). Place the rubber backing pad onto the spindle shaft. Center the sanding disc on top of the backing pad. Insert the lock nut through the disc and thread onto the spindle as far as you can with your fingers. Press in the spindle lock, then tighten the backing pad securely with lock nut wrench (Fig. 8).

TO REMOVE: Reverse procedure.

FIG. 8 SPINDLE

LOCK

SPINDLE

RUBBER

BACKING

PAD

		SANDING
		DISC
	SPIN-ON
	WIRE	LOCK NUT
	BRUSH	LOCK NUT
	BRUSH

WIRE BRUSH ASSEMBLY Before attaching a wire brush be sure its maximum

safe operating speed is not exceeded by the nameplate speed of the tool.

Before assembling wire brush to this tool, disconnect from the power source. Attach hand guard (Fig. 1). Wire brushes are equipped with their own threaded hub, simply thread on to spindle. Be sure to seat against shoulder before turning tool “ON”.

TO REMOVE: Reverse procedure.

WIRE WHEEL ASSEMBLY

Before assembling wire wheel to this tool, disconnect from the power source. Attach Type 27 guard (Fig. 2). Wire wheels are equipped with their own threaded hub, simply thread on to spindle. Be sure to seat against shoulder before turning tool “ON”.

TO REMOVE: Reverse procedure.

MOTOR HOUSING RELEASE LEVER	FIG. 9
(Model 1994-6 & 1994-6D only)
Your tool is equipped with a motor housing
release lever that will allow you to rotate the
spindle in either direction 90˚. To use this
feature, pull release lever in direction of
arrow to release housing, and rotate housing
until it clicks into place (Fig. 9)

-12-

Image 12

Contents Leer antes de usar BM 1609929T61 07-09BM 1609929T61 07-09 7/8/09 137 PMSee Ver la páginaGeneral Power Tool Safety Warnings Power tool use and careSave ALL Warnings Instructions for Future Reference Power Tool-Specific Safety Warnings BM 1609929T61 07-09BM 1609929T61 07-09 7/8/09 137 PM Page Additional Safety Warnings Sanding, sawing, grindingSymbols Symbol Name Designation/ExplanationFunctional Description and Specifications Notches Adjustment ScrewAngle Grinders SpindleFunctional Description and Specifications Assembly Wheel Guard InstallationVibration Control Side Handle Optional Hand GuardAbrasive Type 1A & 27A Wheel Assembly Guard for cuttingType 1 Abrasive Straight Grinding Wheels Spindle Type SPIN-ON Grinding WheelMounting Type 28 or Type Grinding Wheels Flange SET Part no 607 000Flange with Shoulder Sanding Disc Assembly Backing PAD To Install Backing PAD Sanding DiscWire Wheel Assembly Motor Housing Release LeverOperating Instructions Wire Brush Operations Sanding OperationsMaintenance ServiceCleaning Accessories Tool’sVeuillez lire tous les Sécurité du lieu de travailSécurité électrique ’extérieur et réduisent le risque de choc électriqueEntretien Avertissements sur les rebonds et effets associés BM 1609929T61 07-09BM 1609929T61 07-09 7/8/09 138 PM La meuleAvertissements supplémentaires concernant la sécurité Utilisez un protège-main pendant le ponçage et le brossageLe plomb provenant des peintures à base de plomb Symboles Symbole Nom Désignation/ExplicationDescription fonctionnelle et spécifications Rectifieuses d’anglesDescription fonctionnelle et spécifications suite AssemblageEnsemble DE Meule DE Type 27, 28 ET Pour Déposer Inversez la procédureArbre Protecteur DE Meule Type Meule À Visser Écrou DE BlocageMontage DES Meules DE Type 28 OU DE Type Bride OU CONTRE-ÉCROU Broche Bride À ColleretteBride OU CONTRE-ÉCROU Ensemble Daccessoires DE Poncage Disque D’APPUI Métallique Écrou DE Visser BlocageEnsemble DE Brosse Métallique À Touret Consignes de fonctionnement Travaux de ponçage Travaux à la brosse métalliqueChoix DES Disques DE Ponçage Ponçage DU BoisEntretien NettoyageAccessoires ProtecteurSeguridad del área de trabajo Seguridad eléctricaSeguridad personal Servicio de ajustes y reparaciones Uso y cuidado de las herramientas mecánicasRetroceso y advertencias relacionadas BM 1609929T61 07-09BM 1609929T61 07-09 7/8/09 138 PM Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónCon aislamiento doble De Li-ionDescripción funcional y especificaciones Amoladoras angularesSolamente MuescasEnsamblaje Muescas Tornillo DE AjusteProtector DE LA Mano Opcional Ensamblaje de la amoladora Ensamblaje DE LA Rueda DE AmolarEnsamblaje DE LA Rueda Abrasiva DE Tipo 1A Y 27A Ruedas Abrasivas DE Tipo 1 Para Amoladoras RectasMontaje DE Ruedas DE Amolar DE Tipo 28 O DE Tipo Tuerca CON Pestaña O DE Fijación Husillo Pestaña CON ResaltoEnsamblaje de la lijadora Zapata DE SoporteEL Disco DE Lijar Instrucciones de funcionamiento Operaciones de lijado Operaciones con cepillos de alambreMantenimiento ServicioLimpieza Accesorios Protector de la muelaMango lateral Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools