Delta 78-055B instruction manual Adjustments, Assembling Pointer, Adjusting the Fence Parallel

Page 11

ASSEMBLING POINTER

1.Attach right side hairline pointer (UU), Fig. 20 to fence crossarm (VV) Fig. 21 using two #10-32 x 3/8" (9.5 mm) round head screws and flat washers (WW)

Fig. 20.

2.Screws go through the slotted holes in the pointer and into the threaded holes (XX) Fig. 21 in the crossarm.

3.Keep hardware loose for adjustment procedure.

4.Repeat for the left pointer assembly.

ADJUSTMENTS

ADJUSTING THE FENCE PARALLEL

IMPORTANT: CHECK TO MAKE CERTAIN THAT THE MITER GAUGE SLOTS IN THE SAW TABLE ARE PARALLEL WITH THE SAW BLADE. CHECK WITH THE INSTALLATION MANUAL THAT CAME WITH YOUR SAW FOR INSTRUCTIONS.

To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

The fence (YY) Fig. 22, must be adjusted so it is parallel to the miter gauge slot (ZZ). Slide the fence until the bottom edge is in line with the edge of the miter gauge slot as shown and push down on fence locking handle (RR) Fig. 21.

Check to see if the fence (YY) Fig. 22 is aligned with the miter slot the entire length of the table. If an adjustment is needed, lift fence (YY) off the guide as shown in Fig. 23.

Slightly tighten or loosen adjusting screws (A1) Fig. 23 or (B1), using a 3/16" hex wrench, not included. Replace the fence on the guide tube and check again. Repeat this adjustment until you are certain the fence is parallel to the miter gauge slot. NOTE: Very little movement of the adjusting screws is necessary to adjust the fence.

WW

UU

Fig. 20

VV

XX

RR

Fig. 21

YY

ZZ

Fig. 22

YY

B1

A1

Fig. 23

11

Image 11

Contents Biesemeyer T-SquareCommercial Fence System Safety Guidelines Definitions Table of ContentsImportant Safety Instructions General SAFETY RULES Functional Description Carton ContentsHardware for attaching extension table to Unisaw wing Hardware for attaching drawer to the drawer bracketHardware for attaching pointer Hardware for attaching guide tube to front railAttaching Fence Holders to Legs AssemblyAttaching Legs to the Extension Table Attaching Handle to Drawer Attaching Accessory Drawer to Extension TableDrawer Storage for Accessories Rear Rail to SAW Attaching extension table to the right Unisaw wingFront Rail to SAW Attaching rear rail to the Unisaw Attaching Rails to Extension TableAttaching front rail to the extension table Attaching rear rail to extension tableAttaching Guide Tube to Front Rail Fence Clamping Handle AssemblyAssembling Pointer AdjustmentsAdjusting the Fence Parallel Aligning Fence to SAW Blade and Setting Zero Mark Adjusting the Fence TightnessFence Operation MaintenanceTroubleshooting Camfoot PlacementReplacement Parts ServiceAccessories WarrantyUn décès ou des blessures graves LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Blessures gravesRègles DE Sécurité Générales AVANT-PROPOS Description FonctionnelleContenus DE Boite Quincaillerie pour fixer les pointeurs Fixation DES PORTE-GUIDES AUX Pattes AssemblageFixation DES Pattes À LA Rallonge DE Table Fixation DE LA Poignée AU Tiroir Fixation DU Tiroir D’ACCESSOIRES À LA Rallonge DE TableTiroir DE Rangement Pour LES Accessoires Barre DE Guidage Arrière À LA Scie Assemblage DE LA Barre DE Guidage Avant À LA ScieSerrage du contre-écrou sur les pieds de nivellement Fixation de la barre de guidage arrière à la scie UnisawModule DE Poignée SERRE-GUIDE Fixation du tube du guide à la barre de guidage avantRéglage DU Parallélisme DU Guide Assemblage DES PointeursRéglage DU Niveau DE Serrage DU Guide Étalonnage Final DU Guide EntretienMise EN Place DU Pied DE LA Came Fonctionnement DU GuideEntretien ET Réparation Depannage ServiceAccessoiries Pièces DE Rechange Remplacement Gratuit DE L’ÉTIQUETTEGarantie limitée de cinq ans GarantieModeradas Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES Ninguna aplicación de otra manera que para que se diseñóAntes de utilizar la máquina. Al aprender la aplicación Normas Generales DE SeguridadIntroducción Descripción FuncionalContenido DE Carton Artículos de ferretería para anexar los indicadores Cómo Anexar LOS Sujetadores DE LA Guía a LAS Patas EnsambleCómo Anexar LAS Patas a LA Mesa DE Extensión Almacenamiento DE Accesorios EN LA Gaveta Cómo Anexar LA Gaveta DE Accesorios a LA Mesa DE ExtensiónCómo Anexar EL Mango a LA Gaveta Cómo Anexar EL Riel Frontal a LA Sierra Riel trasero a LA SierraCómo anexar el riel trasero a la Unisaw Cómo Anexar LA Mesa DE Extensión a LA SierraCómo anexar el riel frontal a la mesa de extensión Ensamblaje DEL Mango DE Sujeción DE LA Guía Cómo anexar el tubo de la guía al riel frontalCómo Ajustar LA Guía Paralela Cómo Ensamblar EL IndicadorCómo Ajustar LA Tensión DE LA Guía Calibración Final DE LA Guía Colocación DEL PIE DE LevaOperación DE LA Guía Mantenimiento Y Reparaciones Localizacion DE Fallas ServicioAccesorios Excepciones Identificación DelproductoGarantía limitada de cinco años para productos nuevos GarantiaDelta Machinery, Jackson, TN Copyright 2009 Delta Machinery