Delta 78-055B Adjusting the Fence Tightness, Aligning Fence to SAW Blade and Setting Zero Mark

Page 12

ADJUSTING THE FENCE TIGHTNESS

To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

When the fence locking handle (RR) Fig. 24, is pushed to the down position, the fence crossarm (VV) should be completely clamped to the guide tube (C1).

If the fence crossarm (VV) Fig. 24 is not completely clamped to the guide tube (C1) when the handle is pushed down, as shown, lift up handle (RR), raise fence off the guide tube and turn fence around as shown in Fig. 25.

If fence is too loose - slightly tighten the two adjusting screws (A1) Fig. 25 and (B1).

If fence is too tight - loosen the two screws (A1) and (B1) in Fig. 25.

NOTE: Screws (A1) and (B1) should be tightened or loosened an equal amount.

Replace the fence back on the guide tube (C1) Fig. 24 and recheck to see if the fence crossarm is completely tightened to the guide tube with the locking handle (RR) pushed down. Adjust further if necessary.

NOTE: Proper tightening allows about 1/8" (3.2 mm) deflection when the far end of the fence is pushed to one side or the other.

NOTE: Re-check the fence (YY) Fig. 24 and make sure it is still parallel with the miter gauge slot.

ALIGNING FENCE TO SAW BLADE AND SETTING ZERO MARK

1.Move fence (YY) Fig. 26 to the right side of the saw blade so that when you rotate the blade by hand, it just clears the fence when fence is locked, as shown in Fig. 26.

2.Set the right pointer (UU) Fig. 27 to zero and tighten pointer hardware.

NOTE: If the pointer can’t be set to zero, loosen serrated nuts (JJ) Fig. 15 under the guide tube and adjust guide tube as needed. Re-tighten the nuts (JJ).

3.Make a test cut at 1" (25 mm) and verify that the saw is cutting a one-inch piece.

4.If workpiece is not the right length, move pointer as needed and re-check.

5.Move fence body to left side of blade and set the left pointer in the same manner.

YY

VV

C1

RR

Fig. 24

YY

B1

A1

Fig. 25

YY

Fig. 26

UU

Fig. 27

12

Image 12

Contents Biesemeyer T-SquareCommercial Fence System Table of Contents Important Safety InstructionsSafety Guidelines Definitions General SAFETY RULES Carton Contents Functional DescriptionHardware for attaching drawer to the drawer bracket Hardware for attaching pointerHardware for attaching guide tube to front rail Hardware for attaching extension table to Unisaw wingAssembly Attaching Legs to the Extension TableAttaching Fence Holders to Legs Attaching Accessory Drawer to Extension Table Drawer Storage for AccessoriesAttaching Handle to Drawer Attaching extension table to the right Unisaw wing Front Rail to SAWRear Rail to SAW Attaching Rails to Extension Table Attaching front rail to the extension tableAttaching rear rail to extension table Attaching rear rail to the UnisawFence Clamping Handle Assembly Attaching Guide Tube to Front RailAdjustments Adjusting the Fence ParallelAssembling Pointer Adjusting the Fence Tightness Aligning Fence to SAW Blade and Setting Zero MarkMaintenance TroubleshootingCamfoot Placement Fence OperationService AccessoriesWarranty Replacement PartsLES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsBlessures graves Un décès ou des blessures gravesRègles DE Sécurité Générales Description Fonctionnelle Contenus DE BoiteAVANT-PROPOS Quincaillerie pour fixer les pointeurs Assemblage Fixation DES Pattes À LA Rallonge DE TableFixation DES PORTE-GUIDES AUX Pattes Fixation DU Tiroir D’ACCESSOIRES À LA Rallonge DE Table Tiroir DE Rangement Pour LES AccessoiresFixation DE LA Poignée AU Tiroir Assemblage DE LA Barre DE Guidage Avant À LA Scie Barre DE Guidage Arrière À LA ScieFixation de la barre de guidage arrière à la scie Unisaw Serrage du contre-écrou sur les pieds de nivellementFixation du tube du guide à la barre de guidage avant Module DE Poignée SERRE-GUIDEAssemblage DES Pointeurs Réglage DU Parallélisme DU GuideRéglage DU Niveau DE Serrage DU Guide Entretien Mise EN Place DU Pied DE LA CameFonctionnement DU Guide Étalonnage Final DU GuideDepannage Service AccessoiriesPièces DE Rechange Remplacement Gratuit DE L’ÉTIQUETTE Entretien ET RéparationGarantie Garantie limitée de cinq ansInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESNinguna aplicación de otra manera que para que se diseñó ModeradasNormas Generales DE Seguridad Antes de utilizar la máquina. Al aprender la aplicaciónDescripción Funcional Contenido DE CartonIntroducción Artículos de ferretería para anexar los indicadores Ensamble Cómo Anexar LAS Patas a LA Mesa DE ExtensiónCómo Anexar LOS Sujetadores DE LA Guía a LAS Patas Cómo Anexar LA Gaveta DE Accesorios a LA Mesa DE Extensión Cómo Anexar EL Mango a LA GavetaAlmacenamiento DE Accesorios EN LA Gaveta Riel trasero a LA Sierra Cómo Anexar EL Riel Frontal a LA SierraCómo Anexar LA Mesa DE Extensión a LA Sierra Cómo anexar el riel frontal a la mesa de extensiónCómo anexar el riel trasero a la Unisaw Cómo anexar el tubo de la guía al riel frontal Ensamblaje DEL Mango DE Sujeción DE LA GuíaCómo Ensamblar EL Indicador Cómo Ajustar LA Guía ParalelaCómo Ajustar LA Tensión DE LA Guía Colocación DEL PIE DE Leva Operación DE LA GuíaCalibración Final DE LA Guía Localizacion DE Fallas Servicio AccesoriosMantenimiento Y Reparaciones Identificación Delproducto ExcepcionesGarantia Garantía limitada de cinco años para productos nuevosDelta Machinery, Jackson, TN Copyright 2009 Delta Machinery