Delta 78-055B Attaching Rails to Extension Table, Attaching front rail to the extension table

Page 9

Attaching RAILS TO EXTENSION Table

NOTE: Do the next steps in order presented. The extension table and main saw cast iron table must be level and flush to ensure smooth operation of your fence. To get the table level, it is important to attach the pieces in this order:

1.Front rail to the extension table.

2.Rear rail to the extension table.

3.Rear rail to the Unisaw. Though it is already attached, tightening this hardware firmly is the last step.

NOTE: Re-check and make sure the hardware used to attach the rear rail to the Unisaw is only finger tight and allows slight movement of the rear rail up and down.

Attaching front rail to the extension table

1.Position the leveling foot (U) Fig. 13 on the front of the saw until the holes (not visible) in the extension table line up with the holes (EE) in the front rail. (NOTE: 52" (1.3 m) version shown in Figure 13.)

NOTE: Place guide tube (FF) across saw table and onto extension table as shown in Fig. 13. If there is a gap (as shown) the leveling foot (DD) needs to be adjusted to bring the table up more.

2.Insert a 1/4-20 x 3/4" (19 mm) flat head screw into one hole (EE) Fig. 13 on front rail. Place a 1/4-20 serrated flange nut on the screw from underneath the extension table.

3.Repeat this for the remaining holes (EE) Fig. 13 in the front rail.

4.Using template (Z) Fig. 14, check rail position at left side of table as shown, then the right side. Then re-check both left and right side after tightening. The gauge must be fully on the table and just touch the rail surface. See inset Figure 14.

5.When positioned as described above, the horizontal portion of the rail should be down from the top of the table surface 2-7/8” (73.03 mm). Tighten the front rail mounting hardware when you are certain the rail is set at the proper depth. See inset Fig. 14 for cross-section showing where to check for flush.

Attaching rear rail to extension table

NOTE: Do not use template to set rear rail.

Use the same hardware and procedures from steps 1-3 in section Attaching Front Rail to the Extension Table, attach the rear rail to the extension table.

NOTE: Instead of leveling foot (U) Fig. 13, you will position leveling foot (V) just prior to installing rear rail fasteners.

Attaching rear rail to the Unisaw

Fully tighten the two (2) 3/8-24 x 1" (25 mm) hex head screws that attach the rear rail to the Unisaw.

Tightening jam nut on leveling feet

Once feet are set, tighten jam nut (HH) Fig. 14A up against leg body.

FF (GUIDE TUBE)

EE

 

V

U

Fig. 13

Z

Needs to be flush

all along here

Fig. 14

HH

Fig. 14A

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Biesemeyer T-SquareCommercial Fence System Table of Contents Important Safety InstructionsSafety Guidelines Definitions General SAFETY RULES Functional Description Carton ContentsHardware for attaching pointer Hardware for attaching drawer to the drawer bracketHardware for attaching guide tube to front rail Hardware for attaching extension table to Unisaw wingAssembly Attaching Legs to the Extension TableAttaching Fence Holders to Legs Attaching Accessory Drawer to Extension Table Drawer Storage for AccessoriesAttaching Handle to Drawer Attaching extension table to the right Unisaw wing Front Rail to SAWRear Rail to SAW Attaching front rail to the extension table Attaching Rails to Extension TableAttaching rear rail to extension table Attaching rear rail to the UnisawAttaching Guide Tube to Front Rail Fence Clamping Handle AssemblyAdjustments Adjusting the Fence ParallelAssembling Pointer Aligning Fence to SAW Blade and Setting Zero Mark Adjusting the Fence TightnessTroubleshooting MaintenanceCamfoot Placement Fence OperationAccessories ServiceWarranty Replacement PartsMesures DE Sécurité Définitions LES Instructions Importantes DE SureteBlessures graves Un décès ou des blessures gravesRègles DE Sécurité Générales Description Fonctionnelle Contenus DE BoiteAVANT-PROPOS Quincaillerie pour fixer les pointeurs Assemblage Fixation DES Pattes À LA Rallonge DE TableFixation DES PORTE-GUIDES AUX Pattes Fixation DU Tiroir D’ACCESSOIRES À LA Rallonge DE Table Tiroir DE Rangement Pour LES AccessoiresFixation DE LA Poignée AU Tiroir Barre DE Guidage Arrière À LA Scie Assemblage DE LA Barre DE Guidage Avant À LA ScieSerrage du contre-écrou sur les pieds de nivellement Fixation de la barre de guidage arrière à la scie UnisawModule DE Poignée SERRE-GUIDE Fixation du tube du guide à la barre de guidage avantRéglage DU Parallélisme DU Guide Assemblage DES PointeursRéglage DU Niveau DE Serrage DU Guide Mise EN Place DU Pied DE LA Came EntretienFonctionnement DU Guide Étalonnage Final DU GuideAccessoiries Depannage ServicePièces DE Rechange Remplacement Gratuit DE L’ÉTIQUETTE Entretien ET RéparationGarantie limitée de cinq ans GarantiePautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesNinguna aplicación de otra manera que para que se diseñó ModeradasAntes de utilizar la máquina. Al aprender la aplicación Normas Generales DE SeguridadDescripción Funcional Contenido DE CartonIntroducción Artículos de ferretería para anexar los indicadores Ensamble Cómo Anexar LAS Patas a LA Mesa DE ExtensiónCómo Anexar LOS Sujetadores DE LA Guía a LAS Patas Cómo Anexar LA Gaveta DE Accesorios a LA Mesa DE Extensión Cómo Anexar EL Mango a LA GavetaAlmacenamiento DE Accesorios EN LA Gaveta Cómo Anexar EL Riel Frontal a LA Sierra Riel trasero a LA SierraCómo Anexar LA Mesa DE Extensión a LA Sierra Cómo anexar el riel frontal a la mesa de extensiónCómo anexar el riel trasero a la Unisaw Ensamblaje DEL Mango DE Sujeción DE LA Guía Cómo anexar el tubo de la guía al riel frontalCómo Ajustar LA Guía Paralela Cómo Ensamblar EL IndicadorCómo Ajustar LA Tensión DE LA Guía Colocación DEL PIE DE Leva Operación DE LA GuíaCalibración Final DE LA Guía Localizacion DE Fallas Servicio AccesoriosMantenimiento Y Reparaciones Excepciones Identificación DelproductoGarantía limitada de cinco años para productos nuevos GarantiaDelta Machinery, Jackson, TN Copyright 2009 Delta Machinery
Top Page Image Contents