Hitachi C12FSA instruction manual Before Using

Page 12

English

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same voltage as that specified on the nameplate of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned ON the power tool will start suddenly and can cause a serious accident.

3. Check the saw blade for visible defects.

Confirm that the saw blade is free of cracks or other visible damage.

4. Confirm that the saw blade is attached securely to the power tool.

Using the supplied 17mm box wrench, tighten the bolt on the saw blade spindle to secure the saw blade. For details, see Fig. 41-a, Fig. 41-b and Fig. 41-c in the section on “SAW BLADE MOUNTING AND DISMOUNTING”.

5. Check the safety cover for proper operation.

Safety cover is designed to protect the operator from coming into contact with the saw blade during operation of the tool.

Always check that the safety cover moves smoothly and covers the saw blade properly.

Safety Cover

Fig. 7

WARNING: NEVER OPERATE THE POWER TOOL if the safety cover does not function smoothly.

6. Confirm the position of the spindle lock before using the tool.

After installing the saw blade, confirm that the spindle lock has been returned to the retract position before using the power tool (see Fig. 2).

7. Check the lower limit position of the Saw Blade.

Although it was adjusted before shipment, carefully check the height of the saw blade. Confirm that the saw blade can be lowered 11/32" to 13/32" (9mm to 10mm) below the table insert. For details, see the section on “Checking the saw blade lower limit position”.

8. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power cord plug fits properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace the receptacle if it is faulty.

9. Confirm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

10. Trial Run

After confirming that no one is standing behind, the power tool start and confirm that no operating abnormalities exist before attempting a cutting operation.

11. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deflection to confirm that the blade is not noticeably unstable; otherwise vibrations might occur and cause an accident.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Avertissement AdvertenciaContents Meanings of Signal Words Important Safety Instructions for Using ALL Power ToolsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications 12FSAApplications Installation Installing the dust bag, holder, stopper and visesPreparation Before Operation Releasing the locking pinBefore Using Before Cutting Cutting a groove on the guardPositioning the table insert Installing the holders ... Optional accessory Checking the saw blade lower limit positionOblique angle Securing the workpieceUsing an ink line Practical ApplicationsSwitch operation Using the Vise Assembly Standard accessoryCutting Operation Cutting narrow workpieces Press cuttingCutting wide workpieces Slide cutting Bevel cutting procedures Cutting large workpiecesMiter cutting procedures Compound cutting proceduresCrown molding cutting procedures For miter cut setting For bevel cut settingGroove cutting procedures Cutting depth adjustment procedure How to use the dust bag Standard accessorySAW Blade Mounting and Dismounting Cutting easily-deformed materials, such as aluminum sashOverload Protective Device for POLY-V-BELT Mounting the saw blade -a, -b and -cDismounting the saw blade Maintenance and Inspection Replacement of Guard C Replacement of Poly-V-BeltStorage Handle for transportation and carryingService and Repairs CleaningInformations Importantes Signification DES Mots D’AVERTISSEMENTConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utiliser LE Cordon DE Rallonge AppropriéDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications Plage de coupe mixteCadres en bois et en aluminium Préparation Avant L’UTILISATION Libérer la goupille de verrouillageAvant L’UTILISATION Installation de la plaque d’insertion Avant LA CoupeDécoupe d’une encoche dans la protection Vérification de la position de limite inférieure de la lameInstallation des supports ... Accessoires en option Angle obliqueFixation de la pièce Applications Pratiques Utilisation d’un trait d’encreUtilisation de l’ensemble d’étau Accessoire standard Fonctionnement de l’interrupteurCoupe Coupe de pièces minces Coupe à pression simpleCoupe de pièces larges Coupe avec chariot Coupe de pièces volumineuses Procédure de coupe de biseauProcédure de coupe d’onglet Procédures de coupe mixteProcédures de coupe de corniche complexe Réglage d’une coupe d’onglet Réglage d’une coupe de biseauGarde Table du socle Procédures de coupe d’encoche Procédure de réglage de la profondeur de coupeInstallation ET Retrait DE LA Lame Utilisation du sac à copeaux Accessoire standardInstallation de la lame -a, -b et -c Entretien ET Inspection Retrait de la lameInspection de la lame Réglage du tuyau de chariot s’il est relâchéRemplacement de la protection C Inspecter les balais carbone et FigInspection des vis de montage Vérifier si le garde de sécurité fonctionne correctementService APRÈS-VENTE ET Réparations Remplacement de la poly-courroie enPoignée pour le transport GraissageInformación Importante Significado DE LAS Palabras ClaveNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilice EL Cable Prolongador AdecuadoAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Aplicaciones Preparativos Previos a LA Operación InstalaciónLiberación del pasador de bloqueo Antes DE LA Utilización Antes DEL Corte Corte de una ranura en el protectorUbicación del inserto de la mesa Ángulo oblicuo Inmovilización de la pieza de trabajoInstalación de los soportes ... Accesorios opcionales Utilización de una línea de tinta Aplicaciones Prácticas Operación de conmutaciónOperación de corte Corte de piezas de trabajo estrechas Corte a presión Corte de piezas de trabajo anchas Corte con deslizamientoCorte de piezas de trabajo grandes Procedimientos de corte de ingletesProcedimiento de corte de ingletes Procedimientos de corte compuesto Procedimientos de corte con moldura en vérticePara el ajuste de corte de ingletes Para el ajuste del corte en bisel33,9 marca Procedimientos de corte de ranuras Procedimiento de ajuste de la profundidad de corteMontaje Y Desmontaje DE LA Hoja DE Sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a, -b y -c Desmontaje de la hoja de sierra Mantenimiento E Inspección Almacenamiento Reemplazo del protector CReemplazo de la correa en V de polivinilo Manejo para transporteServicio Y Reparaciones LimpiezaPage Page Page Page Page Page Page Page Hitachi Koki Canada Co
Top Page Image Contents