Hitachi C12FSA Overload Protective Device for POLY-V-BELT, Mounting the saw blade -a, -b and -c

Page 23

English

1. Mounting the saw blade (Fig. 41-a, Fig. 41-b and Fig. 41-c)

(1)Press in spindle lock and loosen bolt with 17mm box wrench.

Since the bolt is left-hand threaded, loosen by turning it to the right as shown in Fig. 41-b.

NOTE: If the spindle lock cannot be easily pressed in to lock the spindle, turn the bolt with 17mm box wrench while applying pressure on the spindle lock.

The saw blade spindle is locked when the spindle lock is pressed inward.

(2)Remove the bolt and outside washer (B) and collar (B) as shown in Fig. 41-c. The collar (B) have outside diameter of 1" (25.4mm) as shown in Fig. 41-c.

 

 

 

Bolt

17mm

Spindle Lock

 

Washer (B)

Box Wrench

 

 

 

 

 

 

 

 

 

Tighten

Loosen

Dust Guide

1"(25.4mm)

15.88mm

Washer

Saw Blade

 

(B) Collar

Washer

17mm Box

 

 

(B)

(B) Bolt Wrench

Fig. 41-a

Fig. 41-b

Fig. 41-c

(3) Lift the safety cover and mount the saw blade.

WARNING: When mounting the saw blade, confirm that the rotation indicator mark on the saw blade and the rotation direction of the side cover (L) (see Fig. 1) are properly matched.

(4)Thoroughly clean washer (B) collar (B) and the bolt, and install them onto the saw blade spindle.

(5)Press in the spindle lock and tighten the bolt by turning it to the left by standard accessorie’s wrench (17mm box wrench) as indicated in Fig. 41-b.

CAUTION: * A dust guide is installed inside behind the side cover (L).

When removing or installing the saw blade, do not make contact with the dust guide. Contact may break or chip saw blade tips.

*Confirm that the spindle lock has returned to the retract position after installing or removing the saw blade.

*Tighten the bolt so it does not come loose during operation.

Confirm the bolt has been properly tightened before the power tool is started.

2.Dismounting the saw blade

Dismount the saw blade by reversing the mounting procedures described in paragraph 1 above. The saw blade can easily be removed after lifting the safety cover.

CAUTION: Never attempt to install saw blades larger than 12" (305mm) in diameter. Always install saw blades that are 12" (305mm) in diameter or less.

OVERLOAD PROTECTIVE DEVICE FOR POLY-V-BELT

The power of the motor is transmitted to the saw blade by a Poly-V-Belt. When the Poly-V-Belt becomes overloaded, the overload protective device cuts off the current to stop the motor.

In this case turn the switch off immediately and raise the handle to its initial position. Then turn the switch on and after running the tool for 20 seconds without a load for cooling of the motor. Then start the cutting operation. The Poly-V-Belt or the motor will be damaged if the overload protective device turns off frequently.

CAUTION: When the overload protective device stops the motor, the motor will start by turning the switch on after turning it off. When turning the switch on, make sure that the saw blade is not halfway in the material.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Advertencia AvertissementContents Important Information Meanings of Signal WordsImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts USE Proper Extension Cord Replacement PartsDouble Insulation for Safer Operation Name of Parts Operation and Maintenance12FSA SpecificationsApplications Releasing the locking pin InstallationInstalling the dust bag, holder, stopper and vises Preparation Before OperationBefore Using Positioning the table insert Before CuttingCutting a groove on the guard Securing the workpiece Installing the holders ... Optional accessoryChecking the saw blade lower limit position Oblique anglePractical Applications Using an ink lineUsing the Vise Assembly Standard accessory Switch operationCutting wide workpieces Slide cutting Cutting OperationCutting narrow workpieces Press cutting Cutting large workpieces Bevel cutting proceduresCrown molding cutting procedures Miter cutting proceduresCompound cutting procedures For bevel cut setting For miter cut settingGroove cutting procedures Cutting easily-deformed materials, such as aluminum sash Cutting depth adjustment procedureHow to use the dust bag Standard accessory SAW Blade Mounting and DismountingDismounting the saw blade Overload Protective Device for POLY-V-BELTMounting the saw blade -a, -b and -c Maintenance and Inspection Handle for transportation and carrying Replacement of Guard CReplacement of Poly-V-Belt StorageCleaning Service and RepairsConsignes DE Securite Relatives AUX Outils Électriques Informations ImportantesSignification DES Mots D’AVERTISSEMENT Français Consignes de sécurité spéciales pour cet outil électrique Français Double Isolation Pour UN Fonctionnement Plus SUR Pieces DE RechangeUtiliser LE Cordon DE Rallonge Approprié NOM DES Pièces Utilisation ET EntretienPlage de coupe mixte SpécificationsCadres en bois et en aluminium Libérer la goupille de verrouillage Préparation Avant L’UTILISATIONAvant L’UTILISATION Vérification de la position de limite inférieure de la lame Installation de la plaque d’insertionAvant LA Coupe Découpe d’une encoche dans la protectionFixation de la pièce Installation des supports ... Accessoires en optionAngle oblique Utilisation d’un trait d’encre Applications PratiquesFonctionnement de l’interrupteur Utilisation de l’ensemble d’étau Accessoire standardCoupe de pièces larges Coupe avec chariot CoupeCoupe de pièces minces Coupe à pression simple Procédure de coupe de biseau Coupe de pièces volumineusesProcédures de coupe de corniche complexe Procédure de coupe d’ongletProcédures de coupe mixte Réglage d’une coupe de biseau Réglage d’une coupe d’ongletGarde Table du socle Procédure de réglage de la profondeur de coupe Procédures de coupe d’encocheInstallation de la lame -a, -b et -c Installation ET Retrait DE LA LameUtilisation du sac à copeaux Accessoire standard Réglage du tuyau de chariot s’il est relâché Entretien ET InspectionRetrait de la lame Inspection de la lameVérifier si le garde de sécurité fonctionne correctement Remplacement de la protection CInspecter les balais carbone et Fig Inspection des vis de montageGraissage Service APRÈS-VENTE ET RéparationsRemplacement de la poly-courroie en Poignée pour le transportNormas DE Seguridad Para LAS Herramientas Eléctricas Información ImportanteSignificado DE LAS Palabras Clave Español Español Español Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Piezas DE ReemplazoUtilice EL Cable Prolongador Adecuado Nomenclatura DE Partes Operación Y MantenimientoEspecificaciones Aplicaciones Liberación del pasador de bloqueo Preparativos Previos a LA OperaciónInstalación Antes DE LA Utilización Ubicación del inserto de la mesa Antes DEL CorteCorte de una ranura en el protector Instalación de los soportes ... Accesorios opcionales Ángulo oblicuoInmovilización de la pieza de trabajo Utilización de una línea de tinta Operación de conmutación Aplicaciones PrácticasOperación de corte Corte de piezas de trabajo anchas Corte con deslizamiento Corte de piezas de trabajo estrechas Corte a presiónProcedimiento de corte de ingletes Corte de piezas de trabajo grandesProcedimientos de corte de ingletes Para el ajuste del corte en bisel Procedimientos de corte compuestoProcedimientos de corte con moldura en vértice Para el ajuste de corte de ingletes33,9 marca Procedimiento de ajuste de la profundidad de corte Procedimientos de corte de ranurasMontaje de la hoja de sierra -a, -b y -c Montaje Y Desmontaje DE LA Hoja DE SierraForma de utilizar la bolsa para el polvo Accesorio estándar Desmontaje de la hoja de sierra Mantenimiento E Inspección Manejo para transporte AlmacenamientoReemplazo del protector C Reemplazo de la correa en V de poliviniloLimpieza Servicio Y ReparacionesPage Page Page Page Page Page Page Page Hitachi Koki Canada Co
Top Page Image Contents