English
For miter cut setting
If the turntable has been set to either of the angles described, move the turntable adjusting side handle a little to the right and left to stabilize the position and to properly align the miter angle scale and the tip of the indicator before the operation starts.
For bevel cut setting
Move handle on bevel section to the right and left and check that the position is stable and that the bevel angle scale and the tip of the indicator are properly aligned. Then tighten the clamp lever.
Type of | To process crown molding at |
| To process crown molding at |
|
| ||||||||||||||||||||||||||
positions 1 and 4 in Fig. 28. |
| positions 2 and 3 in Fig. 28. |
|
| |||||||||||||||||||||||||||
Crown |
|
|
| ||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Molding | Miter Angle | Bevel Angle |
|
|
|
|
|
| Miter Angle | Bevel Angle |
|
|
|
|
|
|
| ||||||||||||||
| Setting | Setting |
|
|
|
|
|
| Setting | Setting |
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
| ||||||||||||||||||||||||
45° Type | right 35.3° | left 30° | right 30° | left 35.3° | left 30° | right 30° | |||||||||||||||||||||||||
( |
|
| mark) | ( |
|
|
| mark) | ( |
|
|
|
| mark) | ( |
|
| mark) | ( |
|
|
| mark) | ( |
|
|
|
| mark) | ||
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||
38° Type | right 31.6° | left 33.9° | right 33.9° | left 31.6° | left 33.9° | right 33.9° | |||||||||||||||||||||||||
( |
|
| mark) | ( |
|
|
| mark) | ( |
|
|
|
| mark) | ( |
|
| mark) | ( |
|
|
| mark) | ( |
|
|
|
| mark) | ||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(1)Setting to cut crown moldings at positions q and r in Fig. 28 (see Fig. 29; tilt the head to the left): q Turn the turntable to the right and set the Miter Angle as follows:
* For 45°type crown moldings: 35.3° ( |
| mark) |
* For 38°type crown moldings: 31.6° ( |
| mark) |
|
wTilt the head to the left and set the Bevel Angle as follows:
*For 45°type crown moldings: 30° ( mark)
* For 38°type crown moldings: 33.9° ( mark)
ePosition the crown molding so that the upper surface (A in Fig. 27) contacts the fence as indicated in Fig. 30.
(2)Setting to cut crown moldings at positions w and e in Fig. 28 (see Fig. 31; tilt the head to the left): q Turn the turntable to the left and set the Miter Angle as follows:
* For 45°type crown moldings: 35.3° ( |
| mark) |
* For 38°type crown moldings: 31.6° ( |
| mark) |
|
wTilt the head to the left and set the Bevel Angle as follows:
*For 45°type crown moldings: 30° ( mark)
* For 38°type crown moldings: 33.9° ( mark)
ePosition the crown molding so that the lower surface (B in Fig. 27) contacts the fence as in Fig. 32.
|
|
| Head |
|
| Head |
|
| ||
|
|
| Bevel Angle Scale |
|
| Bevel Angle Scale | ||||
|
|
|
|
|
|
|
| |||
q |
|
|
| w | e | |||||
| r |
|
| |||||||
|
|
|
|
|
|
|
|
| ||
|
|
|
| Fence | Fence |
|
| |||
|
|
|
|
|
|
|
| |||
|
|
|
| Base |
|
|
| Base | ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
Miter | Ang | le Scale |
| Turnt | able | Miter | An | gle Scale | Turnt | able |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Fig. 29 |
|
| Fig. 31 |
|
| ||
Fence |
|
|
| Fence |
|
| ||||
A |
| B | B | A | ||||||
|
|
|
| |||||||
|
|
|
|
|
|
|
| |||
|
|
| Table on Base |
|
| Table on Base | ||||
|
|
| Fig. 30 |
|
| Fig. 32 |
|
| ||
20