Hitachi C12FSA instruction manual Switch operation, Using the Vise Assembly Standard accessory

Page 16

English

1. Switch operation

Lock-off Button

Handle

Hole

Trigger

Switch

Fig. 17

The trigger switch lock-off button is designed to prevent inadvert- ent operation of the power tool. To operate the power tool, it is nec- essary to first fully insert the lock-off button into the hole on the handle as shown in Fig. 17.

The trigger switch will not operate unless the lock-off button has been pushed in.

When the trigger switch is released, the power goes off and the lock-off button automatically returns to its initial position, locking the trigger switch.

WARNING: Always remove the lock-off button from the handle when the power tool is not in use. This will ensure that the power tool cannot be turned on accidentally or by someone (especially a child) who is not qualified to use the power tool. If the lock-off button is left in the handle, serious personal injury can result. Since the lock-off button fits rather tightly, it may be necessary to turn it to the left and right during mounting and removing.

2. Using the Vise Assembly (Standard accessory)

 

Screw Holder

6mm

Knob

Knob Bolt

 

Vise Shaft

Vise

V Shape

Plate

 

Groove

 

Fence

 

8mm Knob Bolt

Workpiece

Fig. 18

The vise assembly can be mounted on either the left fence (Fence (B)) or the right fence (Fence (A)), and can be raised or lowered according to the height of the workpiece.

To raise or lower the vise assembly, first loosen the 8mm knob bolt. As shown in Fig. 18, the vise shaft has three locking grooves into which the tip of the 8mm knob bolt is designed to fit in order to lock the screw holder in the desired position.

To ensure that the tip of the 8mm knob bolt is properly aligned with the desired locking groove on the vise shaft, simply align the upper surface of the fence to either of two grooves on the vise shaft surface or to the lower surface of the screw holder.

Therefore, the vise assembly can be attached in either of three positions to ensure proper height adjustment.

After adjusting the height, firmly tighten the 8mm knob bolt; then turn the upper knob, as necessary, to securely attach the workpiece in position.

CAUTION: Always confirm that the motor head (see Fig. 1) does not contact the vise assembly when it is lowered for cutting. If there is any danger that it may do so, loosen the 8mm knob bolt slightly and move the vise assembly to a position where it will not contact the saw blade.

In case of compound cutting of left bevel angle and left miter angle, a workpiece of up to 45mm can be fixed with a vise assembly mounted on the left side. In case the workpiece height exceeds 45mm, mount the ivse assembly on the opposite side of the inclination of the motor head. For other compound cutting (left bvel + right miter, right bevel + left miter and right bevel + right miter), mount the vise asembly on the opposite side of the inclination of the motor head to avoid the contact of the vise assembly with the motor head.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Avertissement AdvertenciaContents Important Safety Instructions for Using ALL Power Tools Meanings of Signal WordsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications 12FSAApplications Installation Installing the dust bag, holder, stopper and visesPreparation Before Operation Releasing the locking pinBefore Using Cutting a groove on the guard Before CuttingPositioning the table insert Installing the holders ... Optional accessory Checking the saw blade lower limit positionOblique angle Securing the workpieceUsing an ink line Practical ApplicationsSwitch operation Using the Vise Assembly Standard accessoryCutting narrow workpieces Press cutting Cutting OperationCutting wide workpieces Slide cutting Bevel cutting procedures Cutting large workpiecesCompound cutting procedures Miter cutting proceduresCrown molding cutting procedures For miter cut setting For bevel cut settingGroove cutting procedures Cutting depth adjustment procedure How to use the dust bag Standard accessorySAW Blade Mounting and Dismounting Cutting easily-deformed materials, such as aluminum sashMounting the saw blade -a, -b and -c Overload Protective Device for POLY-V-BELTDismounting the saw blade Maintenance and Inspection Replacement of Guard C Replacement of Poly-V-BeltStorage Handle for transportation and carryingService and Repairs CleaningSignification DES Mots D’AVERTISSEMENT Informations ImportantesConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Utiliser LE Cordon DE Rallonge Approprié Pieces DE RechangeDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications Plage de coupe mixteCadres en bois et en aluminium Préparation Avant L’UTILISATION Libérer la goupille de verrouillageAvant L’UTILISATION Installation de la plaque d’insertion Avant LA CoupeDécoupe d’une encoche dans la protection Vérification de la position de limite inférieure de la lameAngle oblique Installation des supports ... Accessoires en optionFixation de la pièce Applications Pratiques Utilisation d’un trait d’encreUtilisation de l’ensemble d’étau Accessoire standard Fonctionnement de l’interrupteurCoupe de pièces minces Coupe à pression simple CoupeCoupe de pièces larges Coupe avec chariot Coupe de pièces volumineuses Procédure de coupe de biseauProcédures de coupe mixte Procédure de coupe d’ongletProcédures de coupe de corniche complexe Réglage d’une coupe d’onglet Réglage d’une coupe de biseauGarde Table du socle Procédures de coupe d’encoche Procédure de réglage de la profondeur de coupeUtilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameInstallation de la lame -a, -b et -c Entretien ET Inspection Retrait de la lameInspection de la lame Réglage du tuyau de chariot s’il est relâchéRemplacement de la protection C Inspecter les balais carbone et FigInspection des vis de montage Vérifier si le garde de sécurité fonctionne correctementService APRÈS-VENTE ET Réparations Remplacement de la poly-courroie enPoignée pour le transport GraissageSignificado DE LAS Palabras Clave Información ImportanteNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Utilice EL Cable Prolongador Adecuado Piezas DE ReemplazoAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Aplicaciones Instalación Preparativos Previos a LA OperaciónLiberación del pasador de bloqueo Antes DE LA Utilización Corte de una ranura en el protector Antes DEL CorteUbicación del inserto de la mesa Inmovilización de la pieza de trabajo Ángulo oblicuoInstalación de los soportes ... Accesorios opcionales Utilización de una línea de tinta Aplicaciones Prácticas Operación de conmutaciónOperación de corte Corte de piezas de trabajo estrechas Corte a presión Corte de piezas de trabajo anchas Corte con deslizamientoProcedimientos de corte de ingletes Corte de piezas de trabajo grandesProcedimiento de corte de ingletes Procedimientos de corte compuesto Procedimientos de corte con moldura en vérticePara el ajuste de corte de ingletes Para el ajuste del corte en bisel33,9 marca Procedimientos de corte de ranuras Procedimiento de ajuste de la profundidad de corteForma de utilizar la bolsa para el polvo Accesorio estándar Montaje Y Desmontaje DE LA Hoja DE SierraMontaje de la hoja de sierra -a, -b y -c Desmontaje de la hoja de sierra Mantenimiento E Inspección Almacenamiento Reemplazo del protector CReemplazo de la correa en V de polivinilo Manejo para transporteServicio Y Reparaciones LimpiezaPage Page Page Page Page Page Page Page Hitachi Koki Canada Co
Top Page Image Contents