Hitachi C12FSA SAW Blade Mounting and Dismounting, Cutting depth adjustment procedure

Page 22

English

Cutting depth adjustment procedure:

(1)Loosen the 8mm wing nut and turn the 8mm depth adjustment bolt by hand.

(2)Adjust to the desired cutting depth by setting the distance between the saw blade and the surface of the base (see b in Fig. 37).

(3)The 8mm wing nut must be properly tightened after the adjustment has been completed.

NOTE: When cutting a single groove at either end of the workpiece, remove the unneeded portion with a chisel.

12. Cutting easily-deformed materials, such as aluminum sash

Materials such as aluminum sash can easily deform when tightened too much in a vise assembly. This will cause inefficient cutting and possible overload of the motor.

When cutting such materials, use a wood plate to protect the workpiece as shown in Fig. 39-a. Set the wood plate near the cutting section.

When cutting aluminum materials, coat the saw blade with cutting oil (non-combustible) to achieve smooth cutting and a fine finish.

Furthermore, if the material flutters during cutting in the lateral direction as well, tighten it with the help of a vise (A) (Code No. 305174) sold separately. (Fig. 39-b)

	Vise	Vise
	Vise	Assembly
	Assembly	Assembly
	Assembly
		Fence
		Wood Plate
Fence	Wood	Vise (A)
	Plate	(Optional
		Accessory)

Aluminum

Sash

Wood Plate	Aluminum Sash
8mm Knob Bolt	8mm Knob Bolt
8mm Knob Bolt
Fig. 39-a	Fig. 39-b

13. How to use the dust bag (Standard accessory)

Duct	Side Cover (R)
	Side Cover (R)
	Side Cover (L)

Dust Bag

Right

Angle

Base

Fig. 40

(1)When the dust bag has become full of sawdust, dust will be blown out of the dust bag when the saw blade rotates.

Check the dust bag periodically and empty it before it becomes full.

(2)During bevel and compound cutting, attach the dust bag at a right angle to the base surface as shown in Fig. 40.

CAUTION: Empty the dust bag frequently to prevent the duct and the safety cover from becom- ing clogged.

Sawdust will accumulate more quickly than normal during bevel cutting.

SAW BLADE MOUNTING AND DISMOUNTING

WARNING: To prevent an accident or personal injury, always turn off the trigger switch and discon- nect the power plug from the receptacle before removing or installing a saw blade.

If cutting work is done in a state where the bolt is not sufficiently tightened, the bolt can get loose, the blade can come off, and the safety cover can get damaged, resulting in injuries.

22

Image 22

Contents Avertissement AdvertenciaContents Important Safety Instructions for Using ALL Power Tools Meanings of Signal WordsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordDouble Insulation for Safer Operation Operation and Maintenance Name of PartsSpecifications 12FSAApplications Preparation Before Operation InstallationInstalling the dust bag, holder, stopper and vises Releasing the locking pinBefore Using Cutting a groove on the guard Before CuttingPositioning the table insert Oblique angle Installing the holders ... Optional accessoryChecking the saw blade lower limit position Securing the workpieceUsing an ink line Practical ApplicationsSwitch operation Using the Vise Assembly Standard accessoryCutting narrow workpieces Press cutting Cutting OperationCutting wide workpieces Slide cutting Bevel cutting procedures Cutting large workpieces Compound cutting procedures Miter cutting procedures Crown molding cutting procedures For miter cut setting For bevel cut settingGroove cutting procedures SAW Blade Mounting and Dismounting Cutting depth adjustment procedureHow to use the dust bag Standard accessory Cutting easily-deformed materials, such as aluminum sashMounting the saw blade -a, -b and -c Overload Protective Device for POLY-V-BELTDismounting the saw blade Maintenance and Inspection Storage Replacement of Guard CReplacement of Poly-V-Belt Handle for transportation and carryingService and Repairs CleaningSignification DES Mots D’AVERTISSEMENT Informations ImportantesConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Utiliser LE Cordon DE Rallonge Approprié Pieces DE RechangeDouble Isolation Pour UN Fonctionnement Plus SUR Utilisation ET Entretien NOM DES PiècesSpécifications Plage de coupe mixteCadres en bois et en aluminium Préparation Avant L’UTILISATION Libérer la goupille de verrouillageAvant L’UTILISATION Découpe d’une encoche dans la protection Installation de la plaque d’insertionAvant LA Coupe Vérification de la position de limite inférieure de la lameAngle oblique Installation des supports ... Accessoires en optionFixation de la pièce Applications Pratiques Utilisation d’un trait d’encreUtilisation de l’ensemble d’étau Accessoire standard Fonctionnement de l’interrupteurCoupe de pièces minces Coupe à pression simple CoupeCoupe de pièces larges Coupe avec chariot Coupe de pièces volumineuses Procédure de coupe de biseauProcédures de coupe mixte Procédure de coupe d’ongletProcédures de coupe de corniche complexe Réglage d’une coupe d’onglet Réglage d’une coupe de biseauGarde Table du socle Procédures de coupe d’encoche Procédure de réglage de la profondeur de coupeUtilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameInstallation de la lame -a, -b et -c Inspection de la lame Entretien ET InspectionRetrait de la lame Réglage du tuyau de chariot s’il est relâchéInspection des vis de montage Remplacement de la protection CInspecter les balais carbone et Fig Vérifier si le garde de sécurité fonctionne correctementPoignée pour le transport Service APRÈS-VENTE ET RéparationsRemplacement de la poly-courroie en GraissageSignificado DE LAS Palabras Clave Información ImportanteNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Utilice EL Cable Prolongador Adecuado Piezas DE ReemplazoAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Operación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Aplicaciones Instalación Preparativos Previos a LA OperaciónLiberación del pasador de bloqueo Antes DE LA Utilización Corte de una ranura en el protector Antes DEL CorteUbicación del inserto de la mesa Inmovilización de la pieza de trabajo Ángulo oblicuoInstalación de los soportes ... Accesorios opcionales Utilización de una línea de tinta Aplicaciones Prácticas Operación de conmutaciónOperación de corte Corte de piezas de trabajo estrechas Corte a presión Corte de piezas de trabajo anchas Corte con deslizamientoProcedimientos de corte de ingletes Corte de piezas de trabajo grandesProcedimiento de corte de ingletes Para el ajuste de corte de ingletes Procedimientos de corte compuestoProcedimientos de corte con moldura en vértice Para el ajuste del corte en bisel33,9 marca Procedimientos de corte de ranuras Procedimiento de ajuste de la profundidad de corteForma de utilizar la bolsa para el polvo Accesorio estándar Montaje Y Desmontaje DE LA Hoja DE SierraMontaje de la hoja de sierra -a, -b y -c Desmontaje de la hoja de sierra Mantenimiento E Inspección Reemplazo de la correa en V de polivinilo AlmacenamientoReemplazo del protector C Manejo para transporteServicio Y Reparaciones LimpiezaPage Page Page Page Page Page Page Page Hitachi Koki Canada Co