Black & Decker CS1014 instruction manual Keep blades sharp and clean, Motor, Intended USE

Page 6

to reduce the risk of kickback

Keep a firm grip on saw with both hands at all times.

Stay alert – exercise control.

Support long overhanging materials. As the material is cut and weakens, it will sag, causing a pinched blade.

Support large panels as shown (Fig. 1). Material supported only at the ends (Fig. 2) will lead to blade pinching.

Avoid sawing overhead. Material can sag and will pinch blade.

1

2

Insure that the material to be cut is clamped

(figure 3) and solidly supported and balanced on a strong, stable and level work surface. Support the work so that the wide portion of the saw shoe is on the portion of the material that doesn’t fall after the cut is made. Never hold cut off piece by hand (figure 4 )

3

4

Keep blades sharp and clean.

Use fence or straight edge guide when ripping. Be careful as the cut off strip can sag or twist, closing the cut and pinching the blade, leading to KICKBACK.

Don’t force tool. Wood variables such as knots, hardness, toughness, wetness, pressure treated and freshly cut green lumber can heavily load the saw which can lead to stalling. Push the saw slower when this occurs.

Don’t remove saw from work during a cut while the blade is moving.

Allow saw to reach full speed before blade contacts material to be cut. Starting the saw with the blade against the work or pushed forward into cut can lead to stalling or sudden backward movement of saw.

Never attempt to lift saw when making a bevel cut. This leads to blade binding and stalling.

Always secure work to prevent workpiece movement during cut.

Do not try to force saw back on line if your cut begins to go off line. This can cause

KICKBACK. Stop saw and allow blade to coast down to a stop. Withdraw from cut and start a new cut on the line.

Set depth adjustment of saw such that one tooth of the blade projects below the workpiece as shown in (figure 7).

Do not back up a rotating blade in the cut. Twisting the saw can cause the back edge of the blade to dig into the material, climb out of the work and run back toward the operator.

Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.

Motor

Be sure your power supply agrees with nameplate marking. 120 Volts AC means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black+Decker tools are factory- tested; if this tool does not operate, check the power supply. This tool is AC only.

INTENDED USE

This circular saw is designed for wood cutting applications. Do not use water feed attachments with this saw. Do not use abrasive wheels or blades. Do not use under wet conditions or in presence of flammable liquids or gases.

Save these instructions

6

Image 6
Contents 4 184mm circular saw General power tool safety warnings Power tool use and care ServiceCauses and operator Prevention of kickback Additional safEty instructions Always observe that the lower guardHertz CCAAmperes WattsMotor Keep blades sharp and cleanAlways secure work to prevent workpiece movement during cut Intended USEAssembly / adjustment set-up Overview figAttaching the blade Switch OperationGuard Against Kickback Service Information MaintenanceAccessories Full Two-Year Home Use WarrantyService center or authorized Possible Cause Possible SolutionServiced at a Black+Decker Unit will not start Cord not pluggedScie circulaires 7-1/4 184mm Sécurité Personnelle Sécurité DU Lieu DE TravailRisques de décharge électrique Utilisation ET Entretien D’UN Outil ÉlectriquePourtouteslesscies Causes de l’effet de Rebond et preévention Par L’opérateurRéparation Directives de Sécurité concernantlamle protége- inférieur Directives de Sécurité Supplémentaires scies CirculairesToujours s’assurer que la scie est propre Page Garder les lames aiguisées et propres Pour Réduire LE Risque ’EFFET DE RebondSerrer fermement la scie avec les deux mains en tout temps MoteurRéglage de l’angle de biseau fig Configuration de ’assemblage et des RéglagesAperçu Général fig Fixation de la lame etConseils pour une utilisation optimale FonctionnementInterrupteur Découpe EN PocheLubrification AccessoiresEntretien Information sur les réparationsSolution possible ProblèmeCause possible Sierras circulares de 184mm 7-1/4 Para registrar su nuevo productoSeguridad Personal  SEGURIDAD EléctricaDescarga eléctrica Utilice equipos de protección personalMantenimiento Instruccionesdeseguridad ParatodaslassierrasCausas del retroceso y su prevención por partedel operador Con ambas manos, no hay riesgo de que la hoja las corteInstrucciones De Seguridad para El Protector inferior Adicionales De SeguridadCon el movimiento del protector inferior de la hoja Reemplace o repare los cables dañadosRetire todos los clavos de la madera antes de cortar Manténgase alerta y en controlMantenga las hojas afiladas y limpias USO PrevistoAjuste de la profundidad de corte y Descripción general figEnsamblado/Ajuste Ajuste del ángulo de biselado figFuncionamiento InterruptorLubricación Almacenamiento de la llaveMantenimiento AccesoriosGarantía completa de dos años para uso en el hogar Causa posible Solución posibleTelephone · No. Teléfono Años DE GarantiaEsta Garantia no Aplica Cuando Av. Universidad No Av. Colón 2915 OteTel 998 884 72 Bolivia No