Honeywell R0512 manual Input/Output Status Text V2.04.xx or higher, Interval Count

Page 26

ATTRIBUTES

 

EXCEL 50/100/500/600/800

PT 1000/2

Hysteresis increases approx. linearly with temperature.

 

Average hysteresis:

1.6 K (2.9 °F)

 

Hyst. At 0 °C (32 °F):

1.3 K (2.3 °F)

 

Hyst. At 400 °C (752 °F):

2.0 K (3.6 °F)

PT 3000 (not with Excel 100C)

Hysteresis increases approx. linearly with temperature.

 

Average hysteresis:

0.8 K (1.4 °F)

 

Hyst. At -45 °C (-49 °F):

0.7 K (1.3 °F)

 

Hyst. At 145 °C (293 °F):

1.0 K (1.8 °F)

Balco 500 (not with Excel 100C)

Hysteresis decreases approx. linearly with temperature.

 

Average hysteresis:

0.9 K (1.6 °F)

 

Hyst. At -50 °C (-49 °F):

1.0 K (1.8 °F)

 

Hyst. At 150 °C (293 °F):

0.7 K (1.3 °F)

 

 

Input/Output Status Text (prior to V2.04.xx)

 

 

2 status texts per digital data output

Two status texts can be assigned to each digital datapoint status. Status texts give

 

an overview of the condition of the sensor or switching device connected to the

 

datapoint.

 

 

 

The associated status text appears in the attribute "Value" depending on the actual

 

point status.

 

 

 

For instance, the status texts could be as follows for a point connected to a digital

 

output:

 

 

 

Digital point status 0:

Status Text:

"Passive”

 

Digital point status 1:

Status Text:

"Active”

Table 9. Relationships between I/O Status, Active State, and Status Text

Input/Output Status

Active State (prior to V.2.04.x)

Status Text

0

0

active

0

1

passive

 

 

 

1

0

passive

1

1

active

Status Text with flexible datapoints The attribute "Status Text" allows you to describe the value sent to the controller by the digital output Pulse 1 and by flexible datapoints. In the case of flexible datapoints of the type "feedback", the status text refers to the value of the feedback flexible datapoint and not to the required value.

Input/Output Status Text (V2.04.xx or higher)

With firmware 2.04.xx or higher, the relationship between physical output status and logical output status as defined by the attribute "Normally Open/Normally Closed" determines the display of the equivalent status text. See section "Normally Open/Normally Closed (V2.04.xx or higher)" on page 28 for details.

Interval Count

Interval count The attribute "Interval Count" shows the totalizer value (pulse x scaling factor) accumulated since the last reset.

Displaying the interval count The attribute "Interval Count" can be viewed on the XI581, XI582, and Excel 50 MMI operating units as well as via the XL-Online Operating Software and building Supervisor front-ends like XBS, EBI and XFI. Based on mathematical rounding, it is

EN2B-0092GE51 R0512

24

Image 26
Contents Excel 50/100/500/600/800 Excel 50/100/500/600/800 Contents Subtype Value Hysteresis Trend CycleValue Write Protection Excel 50/100/500/600/800 Section Sensor Offset added Revision OverviewChange System Overview Overview Programming Datapoints Physical DatapointsFlexible Datapoints Pseudo DatapointsGlobal Datapoints Data PointsMapped Datapoints V2.04.xx or higher Attributes Access LevelAcknowledge Alarm V2.04.xx or higher Status text Active State prior toActive State Excel Alarm Status prior to Alarm DelayAlarm Suppression Alarm Definition Alarm Status V2.04.xx or higherAlarm Type Interval Counter Alarm StatusAttributes Cycle Count Delay Time Switching UpDelay Time Switching Down Descriptors Feedback DelayHigh/Low Alarm/Warning Limits Engineering UnitHours Run Log Hours Since ServicedHours Run Alarm Hysteresis HysteresisExample of alarm hysteresis Trend HysteresisIntrinsic Hysteresis for Analog Input Signals Broadcast HysteresisInput/Output Status Text V2.04.xx or higher Interval CountCharacteristic Interval LimitLast Change Configured Activated Or low By DIP Diagram High By @Pull-Up Resistor Handling By plug-in For DI on AI ImpedanceManual Value LED Mode XF823x, XFL823x, and XFx830x modulesMaintenance Alarm Network Variable V2.04.xx or higher Normally Open/Normally Closed V2.04.xx or higherMotor Run Time Off PhaseOperating Mode Resulting value Manual valueRemote value Subtype Point AlarmsOutput Type Remote value Resulting ValueScaling Factor Safety Position XFx822x, XFx824x, and XFx830x modulesPulse Duration Suppress Point Switching DownSensor Offset Technical Address Switch-On CounterSwitching down Switching down behavior Trend LoggingValue Hysteresis Trend CycleNumber of technical addresses for flexible datapoints ValueRoom Temp.1.10 Flexible datapoint Number of technical addressesWrite Protection List of Datapoint Attributes Attributes Attributes Individual Time Programs Time ProgramsStructure Daily ProgramWeekly Program Annual ProgramToday Function Generating a Time ProgramSpecial Day List Time Programs 04.x Alarm HandlingPrior to Alarm Alarm text Cond Cause/reason English Code # System AlarmsSystem alarms BenefitsAlarm Handling Warm Start With corresponding function of XBS or XL-Online System Alarms Suppression V .04.xx or higher Data Storage User Program AlarmsAlarms Sent across the System Bus Alarm Handling Communication Test ModeDistributed I/O testing V2.04.xx or higher System BusBus Communication AccessBus Initialization Runtime SynchronizationNetwork-Wide Controller Time Synchronization Initialization of Distributed I/O ModulesNew Bus Devices Remote Communication PC CommunicationExcel IRC Point RefreshingRemote Modem Connection Controller Firmware 2.03.xx and Higher Remote Trending dial-upGeneral Controller Firmware 2.04.xx and HigherExcel For all other controllers equipped with Flash EpromsMiscelleanous Customize Windows Default Regional and Language SettingsHBS Country and Language Settings XL40A2MMI Care Country Controllers with Internal Text MMI XL Online CentraLine Country and Language Settings CLTG00MMIGraphic MMI CLMMI00N2x Tiger Controllers with Hex Dec Char Unicode ISO/IEC 10646-12000 Character Name Latin Small Letter L Latin Small Letter O with Diaeresis Character Settings Eastern Europe Latin Small Letter D Latin Small Letter U with Ring Above Latin Capital Letter L with Acute Character Settings Turkey Miscelleanous Latin Small Letter D Latin Capital Letter I with DOT Above Latin Capital Letter G with Breve Procedure 1. In Windows, click StartSettingsControl panel Miscelleanous Miscelleanous Miscelleanous Miscelleanous Modemfaq IndexAutomation and Control Solutions