Honeywell R0512 manual System Alarms Suppression V .04.xx or higher

Page 52

ALARM HANDLING

 

EXCEL 50/100/500/600/800

 

 

 

 

 

Alarm

alarm text

cond.

cause/reason

no.

English)

code #

 

 

 

 

 

A Distributed I/O module was removed from the LONWORKS network or a sensor break or a

109

Hardware Failure

88

sensor short-circuit or missing NV update from a bound NV was detected on a Distributed

 

 

 

I/O module.

110

Hardware OK

89

A missing Distributed I/O module was reconnected to the LONWORKS network or a missing

sensor was reconnected on a Distributed I/O module or a sensor break / short-circuit was

 

 

 

repaired or a missing NV update from a bound NV was supplied.

111

M-Bus (XL50, only)

-

Used only in Excel 50 fixed applications. Shown together with M-Bus-related alarms.

112

OVFL crit. alarms

113

Critical alarm buffer full.

113

OVFL non-crit. al.

114

Non-critical alarm buffer full.

 

 

 

 

114

OVFL trend

115

Remote trend buffer full.

115

NV Bindings lost

116

If the network interface has been changed in CARE and the changed application has been

downloaded, all bindings will be lost.

 

 

 

116

pls upload trends!

117

The remote trend buffer has reached its notification level and should be uploaded in order

to avoid trend buffer overflow.

 

 

 

117

config data def.

118

Configuration data for the remote communication lost or corrupt due to power failure,

EEPROM fault or uncharged gold cap.

 

 

 

118

unauthorized acc.

119

Unauthorized telephone number and/or unauthorized password tried to dial in.

119

out of memory

120

No more memory available for alarm handling.

 

 

 

 

 

 

 

Front-end X is online while remote trend buffer for front-end Y exceeds the notification

120

Please disconnect!

121

level. Terminate dial-up connection with the controller in order to allow it to transmit its

 

 

 

remote trend buffer to front-end Y.

121

front-end not avail.

122

Front-end could not be reached. Line occupied or disconnected.

 

 

 

 

122

config complete

123

Configuration for the remote communication received, accepted and complete.

123

modem device OK

124

Response message to the XBS life check.

124

C bus error

125

No C-Bus communication between remote communication device number and application

device number. Probably the application device number is missing.

 

 

 

125

LON- I/O init start

126

Initialization start of the Distributed I/O modules.

 

 

 

 

126

LON- I/O init done

127

Initialization of the Distributed I/O modules finished.

127

IP-DIO conflict

128

Standard I/O module XF5xx plugged with address of already-used DIO module XFL5xx.

128

Invalid user ID

212

CARE license key tag in the application is incorrect.

 

 

 

 

 

 

 

The user has tried to make more “many-to-one-bindings” during controller runtime than

129

MTO Binding failed

155

were specified during CARE engineering. The “many” relation of a “many-to-one-binding”

(MTO) is specified during CARE engineering. (The entered “many” relation will be used to

 

 

 

calculate the memory space taken from the controller's application memory for the “many-

 

 

 

to-one-binding”.)

 

 

 

In the event of a module defect or power failure (initialization), this alarm is related to the

130

board missing

19

datapoints on this board. The required configuration contains at least one module not

 

 

 

included in the hardware configuration.

 

 

 

In the event of a module defect or power failure (initialization), this alarm is related to the

131

board present

108

datapoints on this board. A module which is part of the required configuration but was

missing in the hardware configuration has been added to the hardware configuration

 

 

 

 

 

 

again.

System Alarms Suppression (V. 2.04.xx or higher)

System alarms can be suppressed during CARE engineering by inserting the "at" sign ("@") at the beginning of the corresponding alarm text in the alarm text file.

In order to avoid alarm showers at power failure and power return, separate system alarms are provided for module power failure and for input failures on the modules (see Table 21).

EN2B-0092GE51 R0512

50

Image 52
Contents Excel 50/100/500/600/800 Excel 50/100/500/600/800 Contents Subtype Value Hysteresis Trend CycleValue Write Protection Excel 50/100/500/600/800 Change Revision OverviewSection Sensor Offset added System Overview Overview Programming Datapoints Physical DatapointsFlexible Datapoints Pseudo DatapointsGlobal Datapoints Data PointsMapped Datapoints V2.04.xx or higher Acknowledge Alarm V2.04.xx or higher Access LevelAttributes Active State Excel Active State prior toStatus text Alarm Suppression Alarm DelayAlarm Status prior to Alarm Status V2.04.xx or higher Alarm TypeAlarm Definition Interval Counter Alarm StatusAttributes Delay Time Switching Down Delay Time Switching UpCycle Count Feedback Delay High/Low Alarm/Warning LimitsDescriptors Engineering UnitHours Run Hours Since ServicedHours Run Log Alarm Hysteresis HysteresisExample of alarm hysteresis Trend HysteresisIntrinsic Hysteresis for Analog Input Signals Broadcast HysteresisInput/Output Status Text V2.04.xx or higher Interval CountCharacteristic Interval LimitConfigured Activated Or low By DIP Diagram High By @ Pull-Up Resistor HandlingLast Change By plug-in For DI on AI ImpedanceMaintenance Alarm LED Mode XF823x, XFL823x, and XFx830x modulesManual Value Network Variable V2.04.xx or higher Normally Open/Normally Closed V2.04.xx or higherOperating Mode Off PhaseMotor Run Time Remote value Manual valueResulting value Point Alarms Output TypeSubtype Remote value Resulting ValuePulse Duration Safety Position XFx822x, XFx824x, and XFx830x modulesScaling Factor Sensor Offset Switching DownSuppress Point Switch-On Counter Switching down Switching down behaviorTechnical Address Trend LoggingValue Hysteresis Trend CycleValue Room Temp.1.10Number of technical addresses for flexible datapoints Flexible datapoint Number of technical addressesWrite Protection List of Datapoint Attributes Attributes Attributes Time Programs StructureIndividual Time Programs Daily ProgramWeekly Program Annual ProgramSpecial Day List Generating a Time ProgramToday Function Time Programs Prior to Alarm Handling04.x System Alarms System alarmsAlarm Alarm text Cond Cause/reason English Code # BenefitsAlarm Handling Warm Start With corresponding function of XBS or XL-Online System Alarms Suppression V .04.xx or higher Alarms Sent across the System Bus User Program AlarmsData Storage Alarm Handling Test Mode Distributed I/O testing V2.04.xx or higherCommunication System BusAccess Bus InitializationBus Communication Runtime SynchronizationNew Bus Devices Initialization of Distributed I/O ModulesNetwork-Wide Controller Time Synchronization PC Communication Excel IRCRemote Communication Point RefreshingRemote Modem Connection Remote Trending dial-up GeneralController Firmware 2.03.xx and Higher Controller Firmware 2.04.xx and HigherExcel For all other controllers equipped with Flash EpromsHBS Country and Language Settings Customize Windows Default Regional and Language SettingsMiscelleanous XL40A2MMI Care Country Controllers with Internal Text MMI XL Online CentraLine Country and Language Settings CLTG00MMIGraphic MMI CLMMI00N2x Tiger Controllers with Hex Dec Char Unicode ISO/IEC 10646-12000 Character Name Latin Small Letter L Latin Small Letter O with Diaeresis Character Settings Eastern Europe Latin Small Letter D Latin Small Letter U with Ring Above Latin Capital Letter L with Acute Character Settings Turkey Miscelleanous Latin Small Letter D Latin Capital Letter I with DOT Above Latin Capital Letter G with Breve Procedure 1. In Windows, click StartSettingsControl panel Miscelleanous Miscelleanous Miscelleanous Miscelleanous Modemfaq IndexAutomation and Control Solutions