GE 4100, 6100 manual Power Connection Kits, Zoneline Chassis Nomenclature

Power Connection Kits

230/208-Volt Line Cord Connection Units

Line Cord	Electric	Electric	Electric	Min. Circuit
	Heat	Heater	Heat	Protection
Kit
	BTUH	Watts	Amps	(Amps)
RAK3153A	8150/7900	2400/2320	11.0/11.6	15
RAK3203A	11200/10900	3300/3200	15.1/16.0	20
RAK3303A	16000/15450	4700/4530	21.2/22.4	30

Electric Heat Amps include electric heater and fan motor current draw.

Each Line Cord Kit has an integral Leakage Current Detection and Interruption (LCDI) or Arc Fault Current Interrupter (AFCI) device as required by National Electrical Code (NEC) and Underwriters Laboratories (UL) for units manufactured after August 1, 2004.

geappliances.com

230/208-Volt Sub-Base and Direct Connected Units

	Direct	Electric	Electric	Electric	Min. Circuit
Sub-Base	Connection	Heat	Heater	Heat	Protection
	Kit	BTUH	Watts	Amps	(Amps)
RAK204D15P	RAK4157	8150/7900	2400/2320	11.0/11.6	15
RAK204D20P	RAK4207	11200/10900	3300/3200	15.1/16.0	20
RAK204D30P	RAK4307	16000/15450	4700/4530	21.2/22.4	30

Electric Heat Amps include electric heater and fan motor current draw.

Units connected through sub-base do not require an LCDI or AFCI device since they are not considered to be line-cord connected. Each 230/208-volt sub-base kit consists of sub-base with appropriate receptacle for minimum circuit amperage, chaseway to route power connector from sub-base to chassis, wiring to connect sub-base to building wiring and a short line cord with 9-pin connector to connect to chassis and plug into receptacle in sub-base.

Short sub-base line cord may not be used without sub-base. Junction box for 230/208-volt chassis must be purchased separately.

RAK4002A for 2900, 3900, 4100, and 6100 series units, RAK4002B for 5800 series units.

265-Volt Sub-Base and Direct Connected Units

Sub-Base	Power	Direct	Electric Heat	Electric Heater	Electric Heat	Min. Circuit Protection
	Connection Kit	Connection Kit	BTUH	Watts	Amps	(Amps)
RAK204E15	RAK5172	RAK5157	8150	2400	9.6	15
RAK204E20	RAK5202	RAK5207	11550	3400	13.3	20
RAK204E30	RAK5302	RAK5307	16350	4800	18.6	30

Electric Heat Amps include electric heater and fan motor current draw.

265-volt units are to be permanently connected in compliance with National Electrical Code and local codes and have a factory-installed junction box on the chassis. Each 265-volt sub-base kit consists of sub-base with appropriate receptacle for minimum circuit amperage, chaseway to route power connector from sub-base to chassis and wiring to connect sub-base to building wiring.

265-Volt Power Connection Kit must be ordered separately.

Important

Essential Elements Ordering Overview

230/208-volt line cord connected units — order line cord kit 230/208-volt sub-base connected units — order sub-base 265-volt units — order sub-base and power connection kit

Zoneline® Chassis Nomenclature

The Zoneline chassis is identified by a model number defining the type of unit, cooling capacity, electrical information and optional features included on the unit. When specifying or ordering the Zoneline chassis, the use of this nomenclature will assure receiving the correct unit.

EXAMPLE

A	Z	6	1	H		1	2	D		A	D
Zoneline		Chassis series			Nominal cooling capacity				Universal
packaged		41=deluxe line cool/			07=7,000 BTUH cooling				power connection
terminal		electric heat			09=9,000 BTUH cooling
chassis		61=deluxe line heat pump			12=12,000 BTUH cooling				Special Features
					15=15,000 BTUH cooling
		Unit type							B=base unit
									C=corrosion treated
		E=cooling with electric				Voltage/Phase/
									D=internal
		resistance heat				Frequency
										condensate
		H=heat pump with electric				D=230/208-Volt,
										removal (ICR)
		resistance heat				single-phase, 60 Hz
										system (heat

E=265-Volt, single-phase,	pump models
60 Hz
	only) (not for
	coastal areas)
	P=Dry Air 25 (4100
	Series only)

3