GE 6100, 4100 manual Receptacles/Sub-Bases, 6 1 H 1 2 D a D

Zoneline® Chassis Nomenclature

The Zoneline chassis is identified by a model number defining the type of unit, cooling capacity, electrical information and optional features included on the unit. When specifying or

EXAMPLE

A Z 6 1 H 1 2 D A D

ordering the Zoneline chassis use of this nomenclature will assure receiving the correct unit.

Receptacles/Sub-Bases

Zoneline	Chassis series
packaged	41=deluxe line cool/
terminal	electric heat
chassis	61=deluxe line
	heat pump

Unit type

E=cooling with electric resistance heat

H=heat pump with electric resistance heat

Nominal cooling capacity		Universal
07=7,000 BTUH cooling		power connection
09=9,000 BTUH cooling
12=12,000 BTUH cooling		Special Features
15=15,000 BTUH cooling		B=base unit
		C=corrosion treated
	Voltage/Phase/	D=internal
	Frequency	condensate
	D=230/208 Volt, single	removal (ICR)
	phase, 60 Hz	system (heat
	E=265 Volt, single phase,	pump models
	60 Hz	only) (not for
		coastal areas)
		P=Dry Air 25

Tandem	Perpendicular	Large tandem		265V 15 Amp		265V 20 Amp		265V 30 Amp
230/208V 15 Amp	230/208V 20 Amp	230/208V 30 Amp		NEMA7-15R		NEMA7-20R;		NEMA7-30R;
NEMA6-15R	NEMA6-20R	NEMA6-30R
Sub-bases
	RAK204U	RAK204D15P	RAK204D20P		RAK204D30P		RAK204E15	RAK204E20	RAK204E30
Voltage	N/A	230/208		230/208	230/208		265	265	265
Amps	N/A	15		20	30		15	20	30
Receptacle	N/A	NEMA6-20R	NEMA6-20R		NEMA6-30R		NEMA7-15R	NEMA7-20R	NEMA7-30R

230/208 Volt sub-bases include appropriate power cord kit.

265 Volt units are to be direct connected. Cordset through enclosed chaseway into interior sub-base receptacle meets the NEC requirements.

Power connection kits are required on all Zoneline® chassis (see chart below).

The correct kit for the installation is determined by the voltage and amperage of the electrical circuit and the means of connecting the unit to the building wiring. If the unit is to be plugged into a receptacle, a line cord kit would be used; if the unit is to be permanently connected, a permanent connection kit would be used. 265 volt cord set units must be installed in compliance with National Electrical Code®.

Power connection kits Required on all models. See specification sheet for heater KW and branch circuit ampacity.

RAK3153/3203/3303	RAK4157/4207/4307	RAK5157/5207/5307
230/208 volt line cord	230/208 volt universal	265 volt universal power
connection kit	power supply kit	supply kit

230/208 volt	Line cord connected units
LCDI Power Connection Kit	RAK3153*	RAK3203*	RAK3303*
Heater KW	2.4/2.32	3.3/3.2	4.7/4.53
Watts	2,400/2,320	3,300/3,200	4,700/4,530
BTUH	8,150/7,900	11,200/10,900	16,000/15,450
Amps	11.0/11.6	15.1/16.0	21.2/22.4
Min. circuit amps	15	20	30
Recommended	15 amp	20 amp	30 amp
protective	time delay	time delay	time delay
device	fuse or breaker	fuse or breaker	fuse or breaker

265 volt Permanent connected units** (Cord set)

RAK5172	RAK5202	RAK5302
2.4	3.4	4.8
2,400	3,400	4,800
8,150	11,550	16,350
9.6	13.3	18.6
15	20	30
15 amp	20 amp	30 amp
time delay fuse	time delay fuse	time delay fuse

230/208 volt		Direct connection kit†
	RAK4157		RAK4207	RAK4307
Heater KW	2.4/2.32		3.3/3.2	4.7/4.53
Watts	2,400/2,320		3,300/3,200	4,700/4,530
BTUH	8,150/7,900		11,200/10,900	16,000/15,450
Amps	11.0/11.6		15.1/16.0	21.2/22.4
Min. circuit amps	15		20	30
Recommended	15 amp		20 amp	30 amp
protective	time delay		time delay	time delay
device	fuse or breaker		fuse or breaker	fuse or breaker

265 volt Direct connection kit†

RAK5157	RAK5207	RAK5307
2.4	3.4	4.8
2,400	3,400	4,800
8,150	11,550	16,350
9.6	13.3	18.6
15	20	30
15 amp	20 amp	30 amp
time delay fuse	time delay fuse	time delay fuse

*RAK3153, RAK3203 and RAK3303 will be transitioning to RAK3153A, RAK3203A and RAK3303A respectively. Old and new models are interchangeable, and there will be no change in performance. **To be used with sub-base

†To be used with sub-base or connection to building wiring

Preliminary specifications subject to change.

52