Quadra-Fire MTVERNINSAE-PMH owner manual Installation and Operation, Hot glass will cause burns

Page 1

R

MT VERNON PELLET INSERT

ADVANCED ENERGY (AE)

Owner’s Manual

Installation and Operation

Models:

Tested and	O-T L	Portland
Listed by		Oregon USA

CUS

OMNI-Test Laboratories, Inc.

MTVERNINSAE-MBK

MTVERNINSAE-PMH

MTVERNINSAE-CSB

MTVERNINSAE-CWL

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and	• Read, understand and	• Leave this manual with
maintenance instruc-	follow these instruc-	party responsible for use
tions included.	tions for safe installa-	and operation.
	tion and operation.

DO DISCARDNOT

WARNING

Please read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow these instructions could result in property damage, bodily injury or even death.

•Do not store or use gasoline or other ﬂ am- mable vapors and liquids in the vicinity of this or any other appliance.

•Do not overﬁ re - If any external part starts to glow, you are overﬁ ring. Reduce feed rate. Overﬁ ring will void your warranty.

•Comply with all minimum clearances to com- bustibles as speciﬁ ed. Failure to comply may cause house ﬁ re.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

•Do not touch glass until it is cooled

•NEVER allow children to touch glass

•Keep children away

•CAREFULLY SUPERVISE children in same room as ﬁ replace.

•Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

•Keep clothing, furniture, draperies and other ﬂ ammable materials away.

CAUTION

Tested and approved for wood pellets, shelled ﬁ eld corn, wheat and black oil sunﬂ ower seeds. Burning of any other type of fuel voids your warranty.

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult local building, ﬁ re ofﬁ cials or authorities having jurisdic- tion about restrictions, installation inspection, and permits.

www.quadraﬁ re.com

7036-135G

November 22, 2011

Image 1

Contents Hot glass will cause burns Installation and OperationLabel Location On Beaded Chain on e behind Right Side Panel Mt. Vernon Pellet Insert AETable of Contents Appliance Certiﬁ cation Listing and Code ApprovalsMobile Home Approved Glass Speciﬁ cationsGetting Started Design, Installation & Location ConsiderationsAppliance Location Floor SupportInspect Appliance and Components Tools And Supplies NeededPre-Use Check List Thermostat Wall Control LocationAppliance Dimensions 3Dimensions and ClearancesBuilt-in Unit Rear Vent with Outside Air Inch Clearance To Exposed Section And Face TrimMasonry and Zero Clearance Fireplaces Mt. Vernon Pellet Insert AE Built-In VerticalFloor Protection Minimum Opening for Masonry and Zero Clearance FireplacesStarter hole Mark area of floor to cut Altering the Factory-Built Fireplace Mt. Vernon Pellet Insert AE Prefabricated Metal ChimneyVenting Termination Minimum Requirements 4Vent InformationDo not Terminate Vent Termination must exhaust above air inlet elevationOptional Battery Back-Up Negative Pressure, Shut-Down and Electrical Power FailureMt. Vernon Pellet Insert AE Avoiding Smoke and Odors Outside AirMt. Vernon Pellet Insert AE Negative Pressure Draft Equivalent Feet of Pipe Mt. Vernon Pellet Insert AE Chimney and Exhaust ConnectionExample of 3 Elbow-Rear Vent Termination Calculation Altitude in Thousands of Feet Mt. Vernon Pellet Insert AE Pipe Selection ChartFull Reline With Outside Air Horizontal 5Venting Systems305mm min. above 305mm min. below 6Mobile Home Never Install in a Sleeping RoomLeveling System 7Appliance Set-UpOutside Air Kit Instructions Removal of Cast Sides Mt. Vernon Pellet Insert AE Hearth SupportSurround & Trim Set, Basic Mt. Vernon Pellet Insert AE Surround and Trim Set CastRebox. Figures 23.1 Optional Log Set Placement InstructionsRebox. Figures 23.3 7036-135G November 22 8Operating Instructions Fire SafetyCombustible/Non-Combustible Materials Fuel Material and Fuel StorageThermostat Wall Control Manual Setting Thermostat Wall Control Automatic SettingAuto-Clean Firepot System General Operating InformationMt. Vernon Pellet Insert AE Before Your First Fire Fire Characteristics and Flame Height Feed Rate AdjustmentFilling the Hopper with Fuel Starting Your First FireClear Space Mt. Vernon Pellet Insert AE Battery Back-up System OptionalMt. Vernon Pellet Insert AE Ignition Cycles Insert Removal Auto-Clean CycleAdditional Screen Messages Mt. Vernon Pellet Insert AE Quick Start Guide Or CWall Control for Reference 74ºF Issues Solutions Frequently Asked QuestionsPossible Cause Corrective Action Error MessageProper Shutdown Procedure Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Before Servicing Your ApplianceAuto-Clean System Inspection & Cleaning General Maintenance and CleaningCleaning Ash Pan Ash Removal from FireboxExample of a dirty heat exchanger Large Clinker Cleaning Heat Exchanger, Drop Tube & ExhaustLoosen all 6 nuts, but do not Remove Cleaning the Glass Cleaning the HopperDoor Latch Inspection Preparing Firebox for Non-Burn SeasonFire and Smoke Risk Bafﬂ e RemovalConvection Blower Replacement Glass ReplacementConvection Blower Replacement Convection Blower Replacement Cont’dReference Materials Thermocouple on Drop Tube Vacuum Switch Power SupplyOverheat Sensor Snap Disc Thermocouple FirepotMt. Vernon Pellet Insert AE Component Locations Feed Motor, Vacuum Switch, Exhaust Blower, Overheat SensorPart number list on following pages Mt. Vernon Pellet Insert AE Exploded DrawingsStocked at Depot At Depot Stocked#38 Feed Assembly 38.5 38.6 38.4 38.3 38.2 38.1 #40 Auto-Clean Motor/Arm Assembly Stocked at Depot #39 Firepot Riser AssemblyAt Depot StockedFasteners SP-MTVS-GD AccessoriesMt. Vernon Pellet Insert AE Mt. Vernon Pellet Insert AE Contact Information