Quadra-Fire MTVERNINSAE-CWL Optional Log Set Placement Instructions, Rebox. Figures 23.1

Page 23

R

G. Optional Log Set Placement Instructions

2 PIECE LOG SET INSTALLATION

1.Place the left log as shown. There are 2 indentations in the bottom of the log to fi t over the screw heads in the

rebox. Figures 23.1 and 23.2.

2.Place the right log in front of the 2 screw heads in the

rebox. Figures 23.3 & 23.4.

CAUTION

Logs are FRAGILE. Use extreme care when handling or cleaning logs.

Left Log

Log fits over screws

Figure 23.1

Log has indentations on the bottom to fit over the screw heads.

Mt. Vernon Pellet Insert (AE)

Right Log

Log rests in front of screws

Figure 23.3

Figure 23.4

NOTICE:

Due to the abrasive nature of a pellet appliance fi re, the logs are not covered under warranty. Any placement vari- ation other than shown here can cause excessive heat and shall void the appliance warranty.

Figure 23.2

November 22, 2011

7036-135G

Page 23

Image 23
Contents Hot glass will cause burns Installation and OperationLabel Location On Beaded Chain on e behind Right Side Panel Mt. Vernon Pellet Insert AETable of Contents Glass Specifi cations Listing and Code ApprovalsAppliance Certifi cation Mobile Home ApprovedFloor Support Design, Installation & Location ConsiderationsGetting Started Appliance LocationThermostat Wall Control Location Tools And Supplies NeededInspect Appliance and Components Pre-Use Check ListAppliance Dimensions 3Dimensions and ClearancesBuilt-in Unit Rear Vent with Outside Air Inch Clearance To Exposed Section And Face TrimMinimum Opening for Masonry and Zero Clearance Fireplaces Mt. Vernon Pellet Insert AE Built-In VerticalMasonry and Zero Clearance Fireplaces Floor ProtectionStarter hole Mark area of floor to cut Altering the Factory-Built Fireplace Mt. Vernon Pellet Insert AE Prefabricated Metal ChimneyTermination must exhaust above air inlet elevation 4Vent InformationVenting Termination Minimum Requirements Do not Terminate VentOutside Air Negative Pressure, Shut-Down and Electrical Power FailureOptional Battery Back-Up Mt. Vernon Pellet Insert AE Avoiding Smoke and OdorsMt. Vernon Pellet Insert AE Negative Pressure Draft Example of 3 Elbow-Rear Vent Termination Calculation Mt. Vernon Pellet Insert AE Chimney and Exhaust ConnectionEquivalent Feet of Pipe Altitude in Thousands of Feet Mt. Vernon Pellet Insert AE Pipe Selection ChartFull Reline With Outside Air Horizontal 5Venting Systems305mm min. above 305mm min. below 6Mobile Home Never Install in a Sleeping RoomOutside Air Kit Instructions 7Appliance Set-UpLeveling System Removal of Cast Sides Mt. Vernon Pellet Insert AE Hearth SupportSurround & Trim Set, Basic Mt. Vernon Pellet Insert AE Surround and Trim Set CastRebox. Figures 23.3 Optional Log Set Placement InstructionsRebox. Figures 23.1 7036-135G November 22 Fuel Material and Fuel Storage Fire Safety8Operating Instructions Combustible/Non-Combustible MaterialsGeneral Operating Information Thermostat Wall Control Automatic SettingThermostat Wall Control Manual Setting Auto-Clean Firepot SystemStarting Your First Fire Fire Characteristics and Flame Height Feed Rate AdjustmentMt. Vernon Pellet Insert AE Before Your First Fire Filling the Hopper with FuelClear Space Mt. Vernon Pellet Insert AE Battery Back-up System OptionalMt. Vernon Pellet Insert AE Ignition Cycles Additional Screen Messages Auto-Clean CycleInsert Removal Wall Control for Reference Or CMt. Vernon Pellet Insert AE Quick Start Guide 74ºF Issues Solutions Frequently Asked QuestionsPossible Cause Corrective Action Error MessageBefore Servicing Your Appliance Quick Reference Maintenance ChartProper Shutdown Procedure 10Maintaining & Servicing Your ApplianceAsh Removal from Firebox General Maintenance and CleaningAuto-Clean System Inspection & Cleaning Cleaning Ash PanExample of a dirty heat exchanger Large Clinker Cleaning Heat Exchanger, Drop Tube & ExhaustLoosen all 6 nuts, but do not Remove Preparing Firebox for Non-Burn Season Cleaning the HopperCleaning the Glass Door Latch InspectionFire and Smoke Risk Baffl e RemovalConvection Blower Replacement Glass ReplacementConvection Blower Replacement Convection Blower Replacement Cont’dReference Materials Thermocouple Firepot Power SupplyThermocouple on Drop Tube Vacuum Switch Overheat Sensor Snap DiscMt. Vernon Pellet Insert AE Component Locations Feed Motor, Vacuum Switch, Exhaust Blower, Overheat SensorPart number list on following pages Mt. Vernon Pellet Insert AE Exploded DrawingsStocked at Depot At Depot Stocked#38 Feed Assembly 38.5 38.6 38.4 38.3 38.2 38.1 #40 Auto-Clean Motor/Arm Assembly Stocked at Depot #39 Firepot Riser AssemblyAt Depot StockedFasteners SP-MTVS-GD AccessoriesMt. Vernon Pellet Insert AE Mt. Vernon Pellet Insert AE Contact Information