Quadra-Fire CB1200MI-MBK, CB1200I Venting Systems, Full Reline With Outside Air Horizontal

Page 15

	R	CB1200-I Pellet Insert


5	Venting Systems

A.Full Reline With Outside Air - Horizontal

CAUTION

Never draw outside combustion air from:

•Wall, floor or ceiling cavity

•Enclosed space such as an attic or garage

WARNING

Fire Risk.

Inspection of Chimney:

•Masonry chimney must be in good condition.

•Meets minimum standard of NFPA 211

•Factory-built chimney must be a minimum 6 inch (152mm) UL103 HT.

NOTE; Use metal plate around exhaust vent pipe and seal all edges with non-flammable insu- lation such as fiberglass, mineral wool or ceramic.

Do not use high temperature caulking materials to seal any edge to prevent furture service- ability.

Outside Air through Rear

Wall (Horizontal)

Figure 15.1

NOTE:

In Canada, where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365.

NOTE:

•Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

•Illustrations/diagrams are not drawn to scale.

•Actual installation may vary due to individual design preference.

February 3, 2010

7014-188B

Page 15

Image 15

Contents Hot glass will cause burns CB1200MI-MBKWelcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Mobile Home Approved Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Listing and Code ApprovalsAppliance Location Design, Installation & Location Consider- ationsDraft CB1200-I Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Thermostat LocationCB1200-I Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List Appliance Dimensions 3Dimensions and ClearancesRear Shroud Kit is Required for Built-In Installation Shown with Rear Vent and Optional Outside AirInch 0mm Clearance to Exposed Section and Face Trim Inches Millimeters Zero Clearance InstallationsNon-Zero Clearance Installations Floor ProtectionConverting R to k Thermal Conductivity k valueThermal Resistance R value Converting k to RS629M, Standard for 650oC FACTORY-BUILT Chimneys Altering the Factory-Built FireplaceVent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart CB1200-I Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Full Reline With Outside Air Horizontal Venting SystemsCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home 7Appliance Set-Up Rear Shroud InstallationAttaching Shroud to Hopper Body Rear Vent Installation PreparationInstalling Rear Shroud For Top Vent InstallationCB1200-I Pellet Insert Outside Air Kit Instructions Adjustable Hopper OptionsGrille Installation To adjust hopperSize 9D x 45W, 2 to 10 Height Adjustment Adjustable Hearth SupportCB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’dBrick Clip Installation CB1200-I Pellet Insert Optional Brick Set InstallationFront Log Thermostat InstallationTop Log, Left RightShelled Field Corn 8Operating InstructionsFuel Size, Material and Storage Wood Pellets Shelled Field Corn Cont’dThermostat Calls For Heat CB1200-I Pellet Insert General Operating InformationBefore Your First Fire Starting Your First FireCB1200-I Pellet Insert Fire Characteristics Feed Rate Adjustment InstructionsIgnition Cycles Issues Solutions CB1200-I Pellet Insert Frequently Asked QuestionsSymptom TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Cont’dTroubleshooting Cont’d Types of Fuel 10Proper Shutdown ProcedureQuick Reference Maintenance Chart Maintaining & Servicing Your ApplianceSee Disposal of Ashes Frequency As needed Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning Ash Pan Cleaning the HopperCleaning the Glass Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning Exhaust PathCleaning Exhaust Blower Requires No Lubrication Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly Immediate Attention and Cleaning is Required CB1200-I Pellet Insert High Ash Fuel Content MaintenanceEred Phillips head screw driver to remove Screws Before removing the side frame. Use a powIgniter Replacement Baffle Removal Reference Materials CB 200-I Pellet InsertComponent Function Snap Disc #1 Convection Blower 125F Vacuum SwitchWiring Harness See .1 below ThermostatControl Box CB1200-I Pellet Insert Component LocationsCB1200-I Pellet Insert Exploded Drawing Important this is Dated Information HOW to Order CB1200-I Pellet Insert Service Parts and AccessoriesDR-CB12-NL-B Stocked At Depot Description Comments Part NumberDescription Comments Part Number StockedCB1200-I Pellet Insert Stocked at Depot FastenersDate of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance LogCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information